The CJ3A Page CJ3B.info

Author Topic: Distributer shaft length  (Read 10997 times)

0 Members and 1 Guest are viewing this topic.

Offline 1955CJ-5

  • Flatfender Master
  • *****
  • Posts: 2360
  • Karma: +0/-1
  • It wasn't always green....
    • View Profile
Re: Distributer shaft length
« Reply #15 on: March 22, 2014, 10:21:46 PM »
If you take the distributor apart do it slowly and take pictures! this little whisker spring is in there....just to hold a little tension but watch for it!

1955 CJ-5, A friend for 58 years....1951 CJ-3A, a new addition. 1929 Model A Ford Closed Cab Pickup...

Offline 1955CJ-5

  • Flatfender Master
  • *****
  • Posts: 2360
  • Karma: +0/-1
  • It wasn't always green....
    • View Profile
Re: Distributer shaft length
« Reply #16 on: March 22, 2014, 10:24:23 PM »
I've not used these fellows but it would be a temptation....

http://willysdistributors.com/id2.html
1955 CJ-5, A friend for 58 years....1951 CJ-3A, a new addition. 1929 Model A Ford Closed Cab Pickup...

Offline macrisel

  • Flatfender Master
  • *****
  • Posts: 639
  • Karma: +0/-0
  • Always in the middle of a project
    • View Profile
Re: Distributer shaft length
« Reply #17 on: March 23, 2014, 10:45:46 PM »
So I worked on things this weekend and found a few things out.

1.  I took apart and cleaned my carb and the accelerator pump seems to be working now.  Things were pretty gummed up and the linkages and springs were sticking.

2........I took my distributer apart and checked my advance and everything seemed to be working as it should.  However, when I put everything back together and installed the distributer back on the jeep.........I am getting no fire to my plugs.  The "gasket" between the breaker plate and the distributer housing was pretty dry rotted.  There was also a felt bushing around the screw that comes out of the distributer and connects to the coil wire that was pretty rotted.  Since I didn't have anything on hand, I reused them.  Now, I'm beginning to wonder if that is my problem.  Can I use cork to reproduce these gaskets or should I try to hunt down replacement?

When I touch a test light to the coil wire on the distributer (with the ignition on) I get nothing.  Moving back to the coil, I get current on the key side of the coil but not on the distributer side....until I unhook the distributer wire.  This leads me to believe the distributer has a short in it somewhere........right?  Where else can I look for a short?

Randy, thanks for the link!  They look like they really go through the distributer and bring it up to snuff.  If I go that route, I am really tempted to update to 12 volt and electronic ignition..... I would like to stay original, but my ignorance of old school is really starting to show....
From what I understand, 12 volt is a little bit more forgiving of problems and that is what the vast majority of my experience is in.  I know there is nothing "wrong" with a 6 volt system, but there might be more "right" with a 12 volt.

Thanks for the help guys.. :(

Offline Carls_jeep

  • Flatfender Master
  • *****
  • Posts: 1746
  • Karma: +0/-0
  • ...
    • View Profile
Re: Distributer shaft length
« Reply #18 on: March 24, 2014, 10:38:25 AM »
There should not be a gasket between the breaker plate and the distributor plate. They should be metal to metal. You will have to replace the insulators in the distributor body where the screw goes through the body to connect the wires to. It is probably shorting out there.

Offline 1955CJ-5

  • Flatfender Master
  • *****
  • Posts: 2360
  • Karma: +0/-1
  • It wasn't always green....
    • View Profile
Re: Distributer shaft length
« Reply #19 on: March 24, 2014, 10:40:07 AM »
It sounds like you have a short all right. Do you have a meter with a continuity function? You can hook it up and wiggle things around and see if there is a short....

There have been a couple of fellows over at the CJ-2a page that have had the electronic ignitions quit working. The thing about points, is they will typically keep working even though the engine may run poorly...when the electronic ignition quits, your done..

Did you replace the little carbon button or use a new cap?

You could probably use a piece of heat-shrink tubing to insulate that stud that goes through the distributor side, along with gasket/cork material on each end....It sounds like maybe the original insulator had already been replaced....
« Last Edit: March 24, 2014, 11:03:44 AM by 1955CJ-5 »
1955 CJ-5, A friend for 58 years....1951 CJ-3A, a new addition. 1929 Model A Ford Closed Cab Pickup...

Offline Bob W

  • Flatfender Master
  • *****
  • Posts: 2309
  • Karma: +0/-0
    • View Profile
Re: Distributer shaft length
« Reply #20 on: March 24, 2014, 01:01:54 PM »
Quote
When I touch a test light to the coil wire on the distributer (with the ignition on) I get nothing.  Moving back to the coil, I get current on the key side of the coil but not on the distributer side....until I unhook the distributer wire.  This leads me to believe the distributer has a short in it somewhere........right?  Where else can I look for a short?
I agree with the posts above, sounds like you have an unwanted ground. Just keep in mind that when the points are closed the test light will not light up on the distributor side of the coil, only when the points are open. Try testing while cranking the engine, the light should flash as the points open and close.
Bob W

Offline macrisel

  • Flatfender Master
  • *****
  • Posts: 639
  • Karma: +0/-0
  • Always in the middle of a project
    • View Profile
Re: Distributer shaft length
« Reply #21 on: March 24, 2014, 03:30:54 PM »
Carl, I may have misspoke but there is not a gasket between the breaker plate and distributer plate..but there is one between the breaker plate and the case of the distributer that was pretty rotten.

Randy, I do have a continuity tester I'll hook up tonight.  I ran out of shop time yesterday.  The heat shrink tubing is a good idea and I'll probably use it along with the cork/rubber gaskets.  Instead of messing with the carbon button, I just replaced the entire cap.

Bob, I will definatly make sure I rotate the motor while I'm checking for current.  Right now, the disty is pulled back out and disassembled on my workbench while I wonder what went wrong.  It is my luck nothing was broke until I fixed it..........

Does anyone have a photo of the original insulators I could copy from?

Offline macrisel

  • Flatfender Master
  • *****
  • Posts: 639
  • Karma: +0/-0
  • Always in the middle of a project
    • View Profile
Re: Distributer shaft length
« Reply #22 on: March 24, 2014, 03:33:18 PM »
Oh, one more thing.  On looking at the link that Randy posted I noticed my distributer does not have a dust cover inside.  Will this really affect anything?

Offline scoutpilot

  • Willys Guru
  • ****
  • Posts: 291
  • Karma: +6/-0
    • View Profile
Re: Distributer shaft length
« Reply #23 on: March 25, 2014, 05:23:44 AM »
[size=12]I venture to say half the distributors out there don't have dust covers. They are another layer of protection from dirt, water, fuel and oil.[/size][/b]
Old fashioned service never goes out of style.
http: // www.oldjeepcarbs.freeforums.net

Offline Carls_jeep

  • Flatfender Master
  • *****
  • Posts: 1746
  • Karma: +0/-0
  • ...
    • View Profile
Re: Distributer shaft length
« Reply #24 on: March 25, 2014, 09:57:30 AM »
Mark, try these people for parts for your distributor. http://willysdistributors.com/ I got it from the G503 site.

Offline macrisel

  • Flatfender Master
  • *****
  • Posts: 639
  • Karma: +0/-0
  • Always in the middle of a project
    • View Profile
Re: Distributer shaft length
« Reply #25 on: March 28, 2014, 12:14:35 PM »
I finally managed to get back out into the shop last night and work on my distributer.  I took great pains to make gaskets to insulate the breaker plate assembly from the distributer housing and used heat shrink tubing to insulate the machine screw where the coil wire hooks up.  I even went so far as to make a gasket to fit on the outside of the distributer over the same screw to (hopefully) keep out some moisture.

After all of that, I took a Dremel with a small wire wheel cleaned up all the contact points to make sure I would get a solid contact on everything.  Finally, I took my meter and checked for continuity and verified I didn't have anything grounding out where it shouldn't be.  To the best of my knowledge, everything appeared to be working as it should....

I then decided to go the extra mile and put the distributer back in the jeep and give it a go.  I made extra sure to get the disty seated into the oil pump and even used a rubber mallet to make sure it was completly bottomed out.  I brought the motor up to TDC, lined up the rotor button and the cap, strapped everything down, pumped the gas twice, kicked the starter.............and the motor hit once, fluttered and died.  One more pump on the gas, kick the starter and the motor hit and took off and started running!  I almost jumped out the seat I was so happy!  I pumped the gas and everything revved up all the way as it should.  What a relief..

I didn't get to take it for a drive due to the monsoon that was going on last night.  I'm hoping this evening or this weekend to take it out and put it through its paces.  It still seems it is running rich, but no more than it was before all this was started two weeks ago.

Fingers crossed!!

Offline 1955CJ-5

  • Flatfender Master
  • *****
  • Posts: 2360
  • Karma: +0/-1
  • It wasn't always green....
    • View Profile
Re: Distributer shaft length
« Reply #26 on: March 28, 2014, 12:25:07 PM »
Hooray!
1955 CJ-5, A friend for 58 years....1951 CJ-3A, a new addition. 1929 Model A Ford Closed Cab Pickup...

Offline Ryan_M

  • Flatfender Master
  • *****
  • Posts: 1704
  • Karma: +0/-0
    • View Profile
Re: Distributer shaft length
« Reply #27 on: March 28, 2014, 02:52:47 PM »
Sweet!!! 12V conversion be damned!!
Current:
'49 CJ3A
'51 CJ3A
'42 Willys MB-T
'47 Bantam T3-C
Previous:
'46 2A
'51 3A
'52 3A
'52 M38
'54 3B
East Coast Wi

Offline macrisel

  • Flatfender Master
  • *****
  • Posts: 639
  • Karma: +0/-0
  • Always in the middle of a project
    • View Profile
Re: Distributer shaft length
« Reply #28 on: March 28, 2014, 04:29:26 PM »
Quote
Sweet!!! 12V conversion be damned!!

Whoa, whoa, whoa....lets not get ahead of ourselves Ryan.. :-?

By the way, if anyone is interested I contacted Willys Distributers (the link Carl and Randy posted) about rebuilding my distributer and they were very polite and seemed very experienced on these ditributers.  However.....due to demands from his day job he stated his current turnaround time was 3-4 months on rebuilds.

Offline 1955CJ-5

  • Flatfender Master
  • *****
  • Posts: 2360
  • Karma: +0/-1
  • It wasn't always green....
    • View Profile
Re: Distributer shaft length
« Reply #29 on: March 28, 2014, 04:40:07 PM »
12 volt...Really?

After all that trouble you went through to repair your generator mount?

It seems to me that the resistor keeps the ignition at 6v anyway, but the starter will crank faster!
1955 CJ-5, A friend for 58 years....1951 CJ-3A, a new addition. 1929 Model A Ford Closed Cab Pickup...