The CJ3A Page CJ3B.info

Author Topic: Leaf Spring Shackles    Left / Right han  (Read 3155 times)

0 Members and 1 Guest are viewing this topic.

Offline Shalka04

  • Willys Fan
  • **
  • Posts: 51
  • Karma: +0/-0
  • Still Plays With Jeeps
    • View Profile
Leaf Spring Shackles    Left / Right han
« on: May 11, 2012, 09:12:39 PM »
If the waether will hold tomorrow i'm putting my axles back on.  I went out and bought new leaf spring shackles, and YES I got two left handed and two right handed.  Do both the right handed thred shackles go on the passanger side and the left handed go on the drivers side.  I've read enough to the point of great confusion so I thought I would ask.  I will post update / status pictures tomorrow as it's raining out.

Thanks in advance,
-John

Offline Bedrock

  • Willys Fan
  • **
  • Posts: 55
  • Karma: +0/-0
    • View Profile
Re: Leaf Spring Shackles � �Left / Right han
« Reply #1 on: May 11, 2012, 10:10:00 PM »
I think one of the left-hand thread shackle bolts goes on the drivers side front, and one goes on the passenger side, rear. �Both go on the bottom, at the spring eye. �I might have to be corrected on this, but that is how I remember it. �If someone has previosly used a right-hand threaded shackle bolt in the spring eye where a left-hand threaded one should go, it can very difficult to replace it with a left-hand threaded one. �I had to use all right-hand threaded shackles on the front of my jeep for that reason.

Hope this is of some help.
« Last Edit: May 11, 2012, 10:44:30 PM by Bedrock »

Offline calvinhunt

  • Flatfender Master
  • *****
  • Posts: 1000
  • Karma: +0/-0
  • Let's keep these great American icons alive!
    • View Profile
Re: Leaf Spring Shackles � �Left / Right han
« Reply #2 on: May 12, 2012, 12:52:02 AM »
Shalka04,
Bedrock is right. �Here is a quote from page 246 of the SERVICE MANUAL for Universal JEEP Vehicles:

"...six bushings are used with right-hand threads and two with left-hand threads. �The right-hand threaded bushings have plain hexagon heads. �The left-hand bushings have a groove around the heads. �The two left-hand threaded U-shackles are identified by a small forged boss on the lower shank of the shackle. �They are used at the left front spring and the right rear spring with the left-hand threaded end DOWN at the spring eye. �The left-hand threaded parts have been cancelled in the production of Models DJ-3A, CJ-3B, CJ-5 and CJ-6"
« Last Edit: May 13, 2012, 01:32:02 AM by calvinhunt »
Calvin
Santa Clara, Utah

Offline Comanche_County

  • Willys Guru
  • ****
  • Posts: 252
  • Karma: +0/-0
    • View Profile
Re: Leaf Spring Shackles � �Left / Right han
« Reply #3 on: May 12, 2012, 07:25:18 PM »
I will freely admit that the next owner of my 51' is going to have to figure that out by trial and error.  Because I think I completely screwed it up.   ;D
Georgia President of the International Flat Fender Club

Offline rocketeer

  • Flatfender Master
  • *****
  • Posts: 1328
  • Karma: +0/-0
  • Support Our Troops.
    • View Profile
Re: Leaf Spring Shackles � �Left / Right han
« Reply #4 on: May 15, 2012, 06:55:09 PM »


Larry

Offline athawk11

  • SMF Administrator
  • Flatfender Master
  • *****
  • Posts: 2818
  • Karma: +0/-1
  • 1949 CJ3A
    • View Profile
Re: Leaf Spring Shackles � �Left / Right han
« Reply #5 on: May 16, 2012, 10:23:44 AM »
PO screwed mine up for me.  All of my shackles are RH thread.

Seems to work.  Not sure why they did LH threads offset in this fashion.

Is there an advantage?

Tim
2-1949 CJ3As
1-1946 CJ2A

Offline rocketeer

  • Flatfender Master
  • *****
  • Posts: 1328
  • Karma: +0/-0
  • Support Our Troops.
    • View Profile
Re: Leaf Spring Shackles � �Left / Right han
« Reply #6 on: May 16, 2012, 11:33:57 AM »
They're designed that way to prevent them from unscrewing from the action of the springs and shackles while you drive.

Larry