The CJ3A Page CJ3B.info

Author Topic: Will this be a problem?  (Read 2671 times)

0 Members and 1 Guest are viewing this topic.

Offline garage gnome

  • Flatfender Master
  • *****
  • Posts: 1947
  • Karma: +0/-0
  • Rustologist
    • View Profile
Will this be a problem?
« on: December 17, 2013, 06:49:43 PM »
Thinking about what I want to do with the fitty-five Chevy. I have access to a set of 4.57 gears for the original rear end. If I do decide to make it 4wd, I can get 4.56 gears for the K20's front axle.

Will the .01 difference be a problem if I use the 4wd?
Nate in Western MA 1953 3A #3268, The Jalopy, '47 2A Wheelin' rig, '49 3A, #37071, unmolested, bone stock named Ted

Offline johnrb3b

  • SMF Administrator
  • Flatfender Master
  • *****
  • Posts: 906
  • Karma: +0/-0
  • No such thing as too many Jeeps - well maybe
    • View Profile
    • Jeeps and stuff
Re: Will this be a problem?
« Reply #1 on: December 17, 2013, 11:35:36 PM »
No.
That's more than the difference you'll get with unequally worn tires.
If you want to be a math fanatic, you're doing it the right way, putting the deeper gears in the back so the front axle will be pulling a bit compared to the rear.
But
In reality the difference is so small the tires will swamp it.
1946 2A - - - 1949 me - older than most of my Jeeps
1954 3B - - - 1957 Wagon - - - 2010 4-door JK
past Jeeps ---> '54 3B - no tub --- '59 3B - no engine
past addiction - VW ---> '69 bus --- '70 camper

Offline garage gnome

  • Flatfender Master
  • *****
  • Posts: 1947
  • Karma: +0/-0
  • Rustologist
    • View Profile
Re: Will this be a problem?
« Reply #2 on: December 18, 2013, 07:58:39 AM »
Ok, thanks!
Nate in Western MA 1953 3A #3268, The Jalopy, '47 2A Wheelin' rig, '49 3A, #37071, unmolested, bone stock named Ted

Offline gmcjr

  • Flatfender Enthusiast
  • ***
  • Posts: 168
  • Karma: +0/-0
  • Even a blind hog finds a acorn every now and then.
    • View Profile
Re: Will this be a problem?
« Reply #3 on: December 19, 2013, 10:08:13 PM »
Most of the factory 4x4 vehicles have that or more of a difference between the front and rear
Gary in N. Texas
51 CJ-3A (old Trusty)
52 Ford 8n (ugly duckling)
46Farmall B (old Rusty)
18 Wrangler Jk

Offline duffer

  • Willys Fan
  • **
  • Posts: 54
  • Karma: +0/-0
  • Just old
    • View Profile
Re: Will this be a problem?
« Reply #4 on: December 20, 2013, 10:19:18 AM »
Quote
Most of the factory 4x4 vehicles have that or more of a difference between the front and rear
Yep.  A lot of examples including the D25/D44 4.09/4.10 sets.  Is the rear axle on that the drop-out style?  I didn't have too good a luck with those not spitting gear teeth out on the street.  On the flip side, very easy to set up.

Nate, what are your plans for the rest of it?  I would very much like to build a 46 3/4 ton Chev using my present 3B engine, SM 465, and NP 203/205 doubled T case.  Probably just going to use D44/D60 axles under it but maybe 60's on both ends.
48 2A, two 49 3A's, 55 3B, 57 FC 170, 57 Wagon, two 68 CJ 5s (both 225's and 4.88), 2006 TJ Rubicon

John, Bozeman, MT

Offline garage gnome

  • Flatfender Master
  • *****
  • Posts: 1947
  • Karma: +0/-0
  • Rustologist
    • View Profile
Re: Will this be a problem?
« Reply #5 on: December 20, 2013, 12:26:16 PM »
If drop out style means that the yoke and carrier all come out in one piece like a ford 9" rear, then yes.

So far it consist of a 350 sbc, 700r4, NP208, stock rear axle, and the K20 front axle (GM 10 bolt). I don't need a radical 4x4. I just want to build it into one and use it to bring engines to engine shows and maybe do a little drag racing...  :o I know, 4.56s are probably not the best gear choice, but it will get off the line fast and with the overdrive, it will have a final ratio of 3.12 which isn't horrible. And if I add a super charger...  ;)
Nate in Western MA 1953 3A #3268, The Jalopy, '47 2A Wheelin' rig, '49 3A, #37071, unmolested, bone stock named Ted

Offline Bill

  • Willys Fan
  • **
  • Posts: 69
  • Karma: +0/-0
  • Still Plays With Jeeps
    • View Profile
Re: Will this be a problem?
« Reply #6 on: January 13, 2014, 10:58:10 AM »
Look for a set of CUCV axles any of the pickups will have 4.56 front and rear, most have a least a rear locker.
1952 USAF M38