The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Steve

Pages: [1] 2 3 ... 7
1
New to the CJ3A world, reading this thread I just realized that this part is missing from my Jeep. I wondered how the vent stop was supposed to work! If you ever fab up more of these, I would be interested in buying one from you.

Steve

2
Thanks for the ideas and pictures.

Steve

3
At a junk store today looking at Jerry cans.  The guy had four crappy cans that were not usable, but one of the cans had a mount on the bottom. I bought it and little did I know that it appears to be an old military jeep Jerry can holder.  At the moment (picture) I am removing the paint. My question is where do folks usually attach this mount? If to the tailgate, do you use a backing plate? Thanks.

Steve

4
The old window frame is actually in pretty good shape. I didn't use it because I ordered the whole kit including the windshield.

It is worth noting that I did not have any issues with the tailgate; it fit fine with everything aligned.  The only other tweaks aside from the windshield have been having to trim tub in order to accommodate the shifters.  The trimming should be largely invisible under the rubber boots.

Two of the most important tools for tub and body part installation are a Dremel tool equipped with a cutoff wheel or a grinding wheel, and a round metal file.  The round file is a particularly quick and effective tool for enlarging and/or extending holes in the sheet metal in order to align bolts with the captive nuts.   

I will try to take some more pictures this weekend.

Steve

5
For those who are following this thread. I tack welded a strip of 18 gauge steel along the bottom of the windshield opening. The guy at the local glass shop indicated that it would fix the problem and he should be able to do the install without the prospect of the windshield popping out.

If I had trimmed the lip down to ~3/8" my repair would have been invisible, with my handiwork, a few of the tack welds will be visible beneath the gasket.

I discovered today that the local paint shop can put any kind of paint one needs into an aerosol spray can, rattle and all.  (This is probably not news to many of you.) A spray can of the vehicle paint proved to be extremely handy for painting the sheet metal strip.

Onward!

Steve

6
I haven't tried there tailgate...I sure hope that I don't have an issue there as well.

7
First major snag today. Took the window frame to the glass shop for mounting the glass only to learn that there is not enough of a lip on the bottom to mount the seal. Apparently, the opening for the window was not cut out symmetrically...to much lip on top, not enough on the bottom. I am likely going to have to weld in a strip on the bottom. Not a happy camper given that the frame is painted.  :-/

8
Tub and various parts went on today. No major glitches, things lined up pretty well lessons learned include:

*Start at the front and work toward back (grille, fenders, etc.)

*Do rear bumper mounts after other tub mounting points are tightened down. There is quite a bit of give in the L-brackets that mount to rear bumper so they can be bent into alignment by tightening the bolts.

I had to cut a notch in the forward part of the cutout for the transfer case shift levers in order for the shifters to have full forward travel. I may have to do a small cutout for the shift lever as well. If the tub could be mounted about 3/4 inch further forward, there would have been no issues.

The big relief was that in all cases, the floor supports rested on the mounting points.

9
Too early to tell. I imagine that there will be plenty of things that come up when we try to get the tub mounted permanently. Wiring might prove challenging as well.  I will post issues as they arise. 

Steve

10
Tub is now painted. Hope to get it mounted this Saturday. Fingers crossed all goes well. The local Chevy dealer body shop did the job.� They were super nice, helpful, and into supporting the project.� They even packed up all of the parts for free without me asking. :)� they also loaned my a sandblaster. Sometimes it's nice to live in a really small town in the middle of nowhere.

Steve

11
Dear Peter,

Sorry to take so long to reply. Work has intervened with the project. However, I did drop all of the bits off at the paint shop today  :).

I purchased the tub from Walcks. It was drop shipped from the distributor.

Steve


12
Battery acid has chewed the crap out of the area under and surrounding the brace the entire vertical length. There are other issues as well.  That isn't to say a more skilled individual than I could fix it up.

13
Wow, now the pressure is on. I went back to the workspace tonight to think about the fender and it's issues. Here is what I learned:

1. I don't think that the issue is with the placement of the support. A few measurements indicate that it should be positioned correctly relative to everything else. I won't know for sure until the fender is mounted.

2.� The problem appears to be interference with the bottom of the fender and the battery holder. Here is my reasoning.� Take a look at the following picture. The original fender is on the left, the new on the right. Note the area on each photo that I highlighted. On the old fender the edge of the fender is aligned with the bracket. On the new fender, the edge of the fender extends beyond (left in this picture) the bracket. This area extended beyond the bracket hits the battery holder and possibly the frame, thus preventing alignment and fender attachment.
�

The good news is that some judicious removal of sheet metal should make things work out. I probably won't get to this stage until the weekend. As a further note, it does appear that the old fender would work fine, so the fitment issue is not due to the tub or tub alignment.

Rommel, if you are interested in my old fender to use as a reference, I would be happy to figure out a way to get it to you.

Steve

14
The BIG DAY, attempting to get the tub on the frame, hoping for not to many issues.

The Good:
The tub hat channels all aligned with the mounting points on the frame. The two center mounting points on the rear bumper lined up perfectly, the outside ones on the left and right were off a bit, but given the bumper has been bashed around, not surprising. Easy fix to make the holes in the braces a bit larger.
 
Drilled holes for mounting and everything seems OK. Steering column is not an issue and the pedals are well aligned with the holes I cut. Probably a little additional elongation of the brake and clutch pedal holes will be needed, but this will be in spec of the original tub.

The Bad:
Left fender top bolt hole will have to be elongated a bit in order to line up with the captive bolts.

The transfer case short shifter just touches the frame when moved forward. Not going to do anything about this one, because things will probably settle in a bit when the vehicle becomes operational. Final solution might be to bend things a tad.

The Ugly:
Right front fender does not want to fit. It looks like the brace is a little about 1/2-3/4 inches forward of where it needs to be in order for things to fit. Contemplation time to see what the simplest remedy will be. Any thoughts would be appreciated.


15
and it for now.  As soon as I get some assistance, I will take a few pictures of the bottom. Overall, the primer paint job looks pretty good, smooth and blemish free. The sheet metal work appears to be pretty good as well.

Pages: [1] 2 3 ... 7