‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Print
Normal Topic DualMatic Hubs (Read 1065 times)
 
TomJ
3A Lover
**
Offline


'51 CJ3A

Posts: 72
Location: Ohio
Joined: 03/12/11
Gender: Male
DualMatic Hubs
05/11/13 at 12:45:53
Print Post  
Hey guys...for any of you who are running DualMatic hubs on your jeep, a question.  Went you assemble the wheels do you put the final nut and washer on the wheel spline? On mine it doesn't look like it will fit inside the outside portion of the hub.

Tom
  
Back to top
 
IP Logged
 
Forum Master
YaBB Administrator
*****
Offline



Posts: 727
Location: Woodbridge, VA
Joined: 11/08/05
Re: DualMatic Hubs
Reply #1 - 05/11/13 at 15:22:06
Print Post  
There is different type of dualmatic hubs.
A short body and a taller one.

Do you have the axle end threaded? If yes then you need the taller body dualmatic type.
  
Back to top
WWW  
IP Logged
 
garage gnome
Flatfender Master
2013 Sponsor Member
*****
Offline


Rustologist

Posts: 1931
Location: Chester
Joined: 02/16/12
Gender: Male
Re: DualMatic Hubs
Reply #2 - 05/12/13 at 00:16:16
Print Post  
The master is right.

You can also cut the threaded end off of the axle. It doesn't "need" to be secured on the end.
  
Nate in Western MA 1953 3A #3268, The Jalopy, '47 2A Wheelin' rig, '49 3A, #37071, unmolested, bone stock named Ted
Back to top
 
IP Logged
 
TomJ
3A Lover
**
Offline


'51 CJ3A

Posts: 72
Location: Ohio
Joined: 03/12/11
Gender: Male
Re: DualMatic Hubs
Reply #3 - 05/12/13 at 14:15:43
Print Post  
OK...I think that answers my question.  I just wasn't sure if the nut that goes on the axle spline needed to be secured or not.  The hubs I have fit over the end of the axle but don't look like they would accommodate the nut if I put it on, so I wasn't sure if it was alright to leave that axle unsecured in there.  I notice it will move back and forth a little bit but cannot disengage from the hub.
Whew ..... I struggled to try and describe that, does all that make sense?

Tom
  
Back to top
 
IP Logged
 
Quebec Jeep
YaBB Administrator
Owner Member 2012
2016 Sponsor Member
2015 Sponsor Member
*****
Offline


CJ-3A 1950

Posts: 1192
Location: Quebec, Canada
Joined: 06/16/12
Gender: Male
Re: DualMatic Hubs
Reply #4 - 05/13/13 at 02:24:28
Print Post  
I will never cut a threaded end axle.  Embarrassed

Here is more info about dualmatic hubs

http://www.cj-2a.com/oldsite/hubs/

Check on the forum here and on the cj2a forum as well, there is a lot of good info about it.
  
I'm jeepcoholic!
Back to top
WWWFacebookYouTube  
IP Logged
 
Page Index Toggle Pages: 1
Print
‹ Previous Topic | Next Topic ›
Bookmarks: Facebook Google Google+ Linked in Twitter Yahoo
 
  « Board Index ‹ Board Top  

The CJ3A Page Forum » Powered by YaBB 2.6.11!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge