Will the jeep be the same color, or has that not yet been decided?

Very nice job.  I'll send mine over.  OD please. 

Thanks Kirkski.  I really appreciate your kind words.  I'm no master.  Just another guy trying to work my way through another Willys rescue.


I decided to try my hand at mounting the rubber.  I watched a couple youtube videos, and determined this was well within my skill set. 

Tools of the trade...



I soaped up the wheel and the rubber. 







I pressed the rim into the tire, then carefully used a couple Wonder bars to guide the first bead over the edge of the rim.







Next, I fed the tube into the tire.  I aligned the valve with the hole in the rim.

I inserted the protective valve stem bushing into the hole then pushed/pulled the tube valve into position.




I then soaped up the rim and tire before working the final bead into the rim.  I used the Wonder Bars and my body weight. 





I filled the tire with air until the beads seated, then let the air out.  I don't know that I needed to do this, but I figured it might let the tube settle in better...just in case it got twisted inside the rim.  I then refilled the tire.


Done.




I saved about $100.00 doing this myself.  I will still take them in to get balanced.

Total time for 5 tire mounts...about 1.5 hours. 


I did an initial "mock up" for the pin stripe.  I'm following the lead set by Ryan on this task.  I mounted the wheel on the Willys.  I taped off the wheel for my initial test. I used a oiled based paint marker by Sharpie.  I spun the wheel while holding the marker to the rim.  The marker was held steady on a temporary platform.  I think this is going to work just fine.







This has been a fun and productive day.  Thanks for looking.

Tim

Hey Brett,
The valve stem protectors were purchased separately.  Big O Tires mounted the wheels for my OD Willys.  The tire guy suggested them.  I figured they were a decent idea.

Yes, there was an air escape around the valve stem that led me to believe I had punctured my first tube.  As I filled the first tire, I could wiggle the valve and air would gush out.  I thought I pinched the tube also.  I was bumbed out.  When it happened on the second tube, I figured pretty quickly that it was the air being displaced from the tire as the tube filled the space.  No way I could have popped both tubes.  Once the bead was set, I let the majority of the air out, then wiggled the valve to let that displaced air out.  I then filled it back up.  Seemed to work fine.

By the way, I was inspired by you doing your own tire mounting.   Thanks!

Tim

One big thing that makes this job easier is the fact using new tires, new tubes and clean, painted rims.  If you ever have to breakdown a 5+ year old tire to replace the tube and then wrestle that thing back on a rusty rim only to find you have MORE leaks after you "fix" it...............paying a tire shop $10-20 to do it on their machine sounds good. 

With that being said, you have to find a good local tire shop that is experienced with tubes.  Your basic kid at Sears tire shop will probably have no idea how to handle tubes and WILL scratch (maybe bend/ruin) your rims.  A lot of time tractor/implement dealerships are the place to go for this.

Great job on the write up and photos!

Time to add pin striping to the wheels.

This is my rig…



This is the oil paint pen…



To stripe the wheels, I mounted each to the rear right side of the Willys.  I set my rig into position, then slowly spun the wheel.  They turned out nice.  They do have that ‘hand painted’ look.  The rig took me about 30 minutes to build.  For set up and painting, each wheel took about 5 minutes.







Mounted the wheels to the Willys.  We have a rolling chassis…

Thanks for the tire tutorial. Never tried it but certainly seemed like something that could be done.

Great job on the pinstripes too. I like the idea of masking off the rim for a trial run. Were you able to get a clean solid stripe with only one full rotation of the wheel or did it take a couple times around? If multiple turns, did your rig stay solid enough to retrace the same stripe or did it veer off and double the width of the stripe at lines?

Regardless, your end result looks about as perfect as you can get.