The CJ3A Page CJ3B.info
« previous next »
Pages: [1]   Go Down

Author Topic: repro dash speedometer doesn't fit  (Read 2531 times)

0 Members and 1 Guest are viewing this topic.

Offline NoCoWillys

  • Willys Fan
  • **
  • Posts: 87
  • Karma: +0/-0
  • Still Plays With Jeeps
    • View Profile
repro dash speedometer doesn't fit
« on: February 25, 2014, 08:16:07 PM »
Hey everyone, been a while since I've been on.  I've been busy reassembling everything and was installing wiring today.  After I finished up all the gauges I had the speedometer left.  I went to install it and it wouldn't fit!!  >:(  I have a repro dash I got from walcks as well as a new speedo from walcks as well.  Anyone else ran into this?  I've had to drill out the light switch hole bigger as well as drill out the ignition switch's hole.  Other than that the new dash seems to have been OK.

nocowillys
Logged
'53 CJ3a

Offline garage gnome

  • Flatfender Master
  • *****
  • Posts: 1947
  • Karma: +0/-0
  • Rustologist
    • View Profile
Re: repro dash speedometer doesn't fit
« Reply #1 on: February 25, 2014, 09:29:15 PM »
Yep, been there, done that. I took a file and made mine bigger. A common issue with the repro parts.
Logged
Nate in Western MA 1953 3A #3268, The Jalopy, '47 2A Wheelin' rig, '49 3A, #37071, unmolested, bone stock named Ted

Offline NoCoWillys

  • Willys Fan
  • **
  • Posts: 87
  • Karma: +0/-0
  • Still Plays With Jeeps
    • View Profile
Re: repro dash speedometer doesn't fit
« Reply #2 on: February 26, 2014, 12:06:03 AM »
That's what I was afraid of.  How much did you have to take off?
Logged
'53 CJ3a

Offline garage gnome

  • Flatfender Master
  • *****
  • Posts: 1947
  • Karma: +0/-0
  • Rustologist
    • View Profile
Re: repro dash speedometer doesn't fit
« Reply #3 on: February 26, 2014, 06:54:24 AM »
I don't remember. Actually, I think I used a dremel because it was faster.
Logged
Nate in Western MA 1953 3A #3268, The Jalopy, '47 2A Wheelin' rig, '49 3A, #37071, unmolested, bone stock named Ted

Offline F Bill

  • Flatfender Master
  • *****
  • Posts: 1402
  • Karma: +1/-0
    • View Profile
Re: repro dash speedometer doesn't fit
« Reply #4 on: February 26, 2014, 10:13:35 AM »
If I was a betting man I would bet that dash is old stock.. This is one of the well known past issues of the MD Juan products....and I have heard from 1/16 to 1/8 too small.

Fortunately it is too small a hole and you don't have to do any more than file the hole out.....too big a hole would be way worse..

I'd still send Dan or Rommel a note with some photos and details of where you bought it in case a bad one slipped thru.
Logged
Owner of the world famous?? Pintojeep 3A and one yet to be named stock project 3A.
Based in central TX and upstate NY.

Offline macrisel

  • Flatfender Master
  • *****
  • Posts: 639
  • Karma: +0/-0
  • Always in the middle of a project
    • View Profile
Re: repro dash speedometer doesn't fit
« Reply #5 on: February 26, 2014, 05:53:10 PM »
Quote
That's what I was afraid of.� How much did you have to take off?

I had the same issue.  I also just used a Dremel tool with a course sanding drum and opened mine up a bit.  The hole wasn't much too small........but enough no amount of forcing could get it to fit.
Logged

Offline NoCoWillys

  • Willys Fan
  • **
  • Posts: 87
  • Karma: +0/-0
  • Still Plays With Jeeps
    • View Profile
Re: repro dash speedometer doesn't fit
« Reply #6 on: February 26, 2014, 08:17:59 PM »
Thanks for the tips.  I'll get my dremel out and go to town. 
Logged
'53 CJ3a
Pages: [1]   Go Up
« previous next »