The CJ3A Page CJ3B.info

Author Topic: What to keep  (Read 3440 times)

0 Members and 1 Guest are viewing this topic.

Offline James P

  • Willys Fan
  • **
  • Posts: 78
  • Karma: +0/-0
  • Still Plays With Jeeps
    • View Profile
What to keep
« on: June 24, 2012, 12:43:42 PM »
A question for those that have purchased the body kits. What actually comes with it and what do I hold on to from the old body?
I am currently stripping the the jeep down and taking everything I can off the old body. I do not want to give up on something and find out that it is hard to get a hold of. Also I am going to hold on the the entire dash assembly since I know that the new one will not be right most likely.
What else would be important to hold on to?
1952 CJ3A

Offline Ryan_M

  • Flatfender Master
  • *****
  • Posts: 1704
  • Karma: +0/-0
    • View Profile
Re: What to keep
« Reply #1 on: June 24, 2012, 09:22:06 PM »
This doesn't answer your specific question but I held onto pretty much every component I took off my Jeep. It was surprising how many times I went wallowing back through that pile of discarded parts to either scavenge a component or just to look at the old one to see how the new one was supposed to work. In a couple cases, after being disappointed with a new part, I went back and salvaged the old one instead. One afternoon I even used the old plug wires and the old cracked distributor cap while troubleshooting and trying to isolate an engine problem. I'd think that with the body parts I'd save EVERYTHING until the new one is on and you're happy with it.
Current:
'49 CJ3A
'51 CJ3A
'42 Willys MB-T
'47 Bantam T3-C
Previous:
'46 2A
'51 3A
'52 3A
'52 M38
'54 3B
East Coast Wi

Offline F Bill

  • Flatfender Master
  • *****
  • Posts: 1402
  • Karma: +1/-0
    • View Profile
Re: What to keep
« Reply #2 on: June 24, 2012, 09:30:31 PM »
Any and all bolt ons, and the tabs underneath that return springs attach to, and anything parking brake related.   And then, keep the whole thing until you are done to measure from when drilling new holes, and to give to another jeep nut when you finish.
Owner of the world famous?? Pintojeep 3A and one yet to be named stock project 3A.
Based in central TX and upstate NY.

Offline bretto

  • Willys Guru
  • ****
  • Posts: 486
  • Karma: +0/-0
  • OD 3A cousin
    • View Profile
Re: What to keep
« Reply #3 on: June 24, 2012, 11:16:11 PM »
I agree with everyone on keeping everything, that includes then tub.  Heck, I even kept all the rusted body parts and sheet metal I cut off.  I've reference back to a that pile of 'scrap' many times.
Brett Orem, UT� [size=14]PHOTO DIARY OF MY BUILD[/size][/URL]

Offline calvinhunt

  • Flatfender Master
  • *****
  • Posts: 1000
  • Karma: +0/-0
  • Let's keep these great American icons alive!
    • View Profile
Re: What to keep
« Reply #4 on: June 25, 2012, 01:05:45 AM »
I reworked the new tub with the old tub next to it.  Both were sitting on saw horses.  I had acquired a free nearly complete parts Jeep (CJ-2A) that I kept just out back.  The old tub and the parts Jeep were not removed from the project construction site until the project was complete and driving.  Valuable info and parts were provided by the nearby extras. If space is a premium just keep your old tub out back but near by till your finished.  
Calvin
Santa Clara, Utah

Offline athawk11

  • SMF Administrator
  • Flatfender Master
  • *****
  • Posts: 2818
  • Karma: +0/-1
  • 1949 CJ3A
    • View Profile
Re: What to keep
« Reply #5 on: June 25, 2012, 12:44:09 PM »
I agree with the others whole heartedly.  Keep it all until complete.

Funny thing, as Brett mentions keeping the old sheet metal he cut out, I did the same.  When I was done with my Willys, I had a very hard time throwing the old sheet metal chunks away.  My wife thought I was crazy, but I had developed sentimental feelings for those old rusty remnants.  I eventually did toss it.

Tim

2-1949 CJ3As
1-1946 CJ2A

Offline James P

  • Willys Fan
  • **
  • Posts: 78
  • Karma: +0/-0
  • Still Plays With Jeeps
    • View Profile
Re: What to keep
« Reply #6 on: June 25, 2012, 05:56:29 PM »
The biggest problem I have is storage space and nosy village counsel members. Plus I have 4 daughters helping me with the rebuild and need to keep the wasp magnets down.
1952 CJ3A

Offline johnrb3b

  • SMF Administrator
  • Flatfender Master
  • *****
  • Posts: 906
  • Karma: +0/-0
  • No such thing as too many Jeeps - well maybe
    • View Profile
    • Jeeps and stuff
Re: What to keep
« Reply #7 on: June 28, 2012, 01:16:22 PM »
If this is what you're looking for:
I just bought a new MD Juan 3B tub - just tub, not a full body kit. It came with:
1) windshield pivot brackets
2) mirror bracket - driver side
3) toolbox lid - but NO gasket
4) NO passenger seat hinges - but there IS the backstop tab on the rear wheel housing
5) tailgate hinges and chain brackets
6) dead flat dash, NO holes, NO stamping for hand brake handle, NO brace, NO flange to mate with steering column bracket
7) NO holes in foot board for gas, brake, clutch, steering wheel, dimmer switch, starter switch
8) there IS a removable cover for the transmission tower cutout in the floor - it's not exactly like original, but it works - NO threaded hole for the mushroom footrest
9) there are 2 or 3 holes in the firewall - they don't match anything on a 3B
10) NO holes in rear for taillights

That's all I can do off the top of my head.
I should take pictures. Maybe this weekend.
1946 2A - - - 1949 me - older than most of my Jeeps
1954 3B - - - 1957 Wagon - - - 2010 4-door JK
past Jeeps ---> '54 3B - no tub --- '59 3B - no engine
past addiction - VW ---> '69 bus --- '70 camper