The CJ3A Page CJ3B.info

Author Topic: Stealerships  (Read 2752 times)

0 Members and 1 Guest are viewing this topic.

Offline NoCoWillys

  • Willys Fan
  • **
  • Posts: 87
  • Karma: +0/-0
  • Still Plays With Jeeps
    • View Profile
Stealerships
« on: August 28, 2012, 12:32:11 AM »
Well the fuel injection control module died in my 2005 f250 diesel.  My local dealership wanted $1300 to replace it and then "further investigate other issues."  I can get my ficm repaired and upgraded for less that $500.  It took me 15 minutes to pull this afternoon.  I know not all dealerships try to rip people off, but this is just insulting.  I know some people might give me crap about having the 6.0L in my diesel, but this is seriously the only problem I've had in it.  120k miles!
'53 CJ3a

Offline 52withaGPW

  • Project Jeep (Newbie)
  • *
  • Posts: 25
  • Karma: +0/-0
  • Bone stock 1952 CJ3A.
    • View Profile
Re: Stealerships
« Reply #1 on: August 28, 2012, 01:00:39 AM »
A buddy of mine recently had the gasket and seal, on the oil pan fitting of his '97 Powerstroke blow out. Blew oil everywhere. It's that funky little fitting that the dipstick tube presses into.

Called the local Ford dealership, and they quoted him $1700, and a day's work, to replace the fitting and seals. Claimed that they would have to pull the engine to drop the pan out (which I can understand. Not enough clearance to drop it down far enough, and the crossmember is riveted to the frame).

Turns out all you need is the $20 gasket and seal kit, as well as a $2.50 .45 caliber cleaning brush and cleaning rod, to hold the fitting in place so you can install the new o-ring and gasket. ;D

Offline p3ferris

  • Willys Guru
  • ****
  • Posts: 249
  • Karma: +0/-0
  • Still Plays With Jeeps
    • View Profile
Re: Stealerships
« Reply #2 on: August 28, 2012, 08:05:27 AM »
I do not tink this would happen if they paid the workers a real good wage and there was no commission.

Offline NoCoWillys

  • Willys Fan
  • **
  • Posts: 87
  • Karma: +0/-0
  • Still Plays With Jeeps
    • View Profile
Re: Stealerships
« Reply #3 on: September 01, 2012, 08:04:29 PM »
Well a week later I'm fixed again.  Looks like this is the 3rd module this truck has had.  Not good for only 7 years old.  This one was rebuilt with better components though so I'm hoping it will last longer.  

Don't get me wrong, I think the mechanics get the short end of the stick a lot of the time, but I also know they aren't the ones that set the prices on stuff.  Then again, if they paid the mechanics more, that would just increase the cost on us...
'53 CJ3a

Offline Gunslinger

  • Flatfender Master
  • *****
  • Posts: 942
  • Karma: +0/-0
  • Cj3a, M38A1,
    • View Profile
Re: Stealerships
« Reply #4 on: September 03, 2012, 10:55:08 PM »
I saw an add here in Mpls, starting wage for a certified auto tech at the big dealerships is 80k.   That's 40 an hour. Pretty good dogh for right out of school. It most likely includes some overtime, but still it's good cash.
Climbs trees, hides in the long grass, hangs out with wet dogs...

Offline Bob W

  • Flatfender Master
  • *****
  • Posts: 2309
  • Karma: +0/-0
    • View Profile
Re: Stealerships
« Reply #5 on: September 04, 2012, 08:28:02 PM »
Quote
I saw an add here in Mpls, starting wage for a certified auto tech at the big dealerships is 80k. � That's 40 an hour. Pretty good dogh for right out of school. It most likely includes some overtime, but still it's good cash.


What is the labor rate for repairs at a dealer in Mpls?
Bob W

Offline Gunslinger

  • Flatfender Master
  • *****
  • Posts: 942
  • Karma: +0/-0
  • Cj3a, M38A1,
    • View Profile
Re: Stealerships
« Reply #6 on: September 04, 2012, 08:58:55 PM »
It's well over 100 per hour
Climbs trees, hides in the long grass, hangs out with wet dogs...