The CJ3A Page CJ3B.info

Author Topic: Annabel's ready  (Read 2224 times)

0 Members and 1 Guest are viewing this topic.

Offline Carls_jeep

  • Flatfender Master
  • *****
  • Posts: 1746
  • Karma: +0/-0
  • ...
    • View Profile
Annabel's ready
« on: August 28, 2012, 04:41:22 PM »
Annabel now has a winch and high water ability. I put John Deere Corn Head grease in the steering knuckles, removed the rear axle cover and modified it for a vent, welded the vent hole in the axle tube and installed deep water vents. Tomorrow I will load her on the trailer and pack up everything and head for Utah Thursday morning.

YEEEEEEEEEEHAAAAAAAAA

Offline NoCoWillys

  • Willys Fan
  • **
  • Posts: 87
  • Karma: +0/-0
  • Still Plays With Jeeps
    • View Profile
Re: Annabel's ready
« Reply #1 on: August 28, 2012, 09:43:41 PM »
Nice!  Do you have any pics of the deep water vents?
'53 CJ3a

Offline Carls_jeep

  • Flatfender Master
  • *****
  • Posts: 1746
  • Karma: +0/-0
  • ...
    • View Profile
Re: Annabel's ready
« Reply #2 on: August 28, 2012, 11:42:53 PM »
I took a photo of the inside and outside of the rear cover modification I can post. I could take a photo of each hose setup but that is not needed. I pulled the vent out of the front cover and put a hose barb in and ran a hose up the side of the radiator with clamps about even with the top of the fender. The rear setup has an elbow with a barb in it and a hose going forward, over the frame and up a hole I cut in the floor with a 1/2" conduit cutter. The hole is 7/8" diameter for a grommet to protect the hose and the hose is clamped to the side of the right rear fender behind the passenger seat. The top of each hose has a barb fitting that I screwed the vent into. You need to allow some slack for the travel of the axle so it don't rip the hose off and route it so it's protected as much as possible.



« Last Edit: August 28, 2012, 11:45:14 PM by Carlsjeep »

Offline NoCoWillys

  • Willys Fan
  • **
  • Posts: 87
  • Karma: +0/-0
  • Still Plays With Jeeps
    • View Profile
Re: Annabel's ready
« Reply #3 on: August 29, 2012, 12:03:47 AM »
Very nice. Thanks.  We don't have tons of water here, but the mountain streams here in Colorado can be surprisingly deep.
'53 CJ3a

Offline bretto

  • Willys Guru
  • ****
  • Posts: 486
  • Karma: +0/-0
  • OD 3A cousin
    • View Profile
Re: Annabel's ready
« Reply #4 on: August 29, 2012, 12:31:36 PM »
Good to hear Carl, hope your drive is enjoyable. �Are you doing this drive in 2 or 3 days? �Either way thats a lot of windshield time.
Drive safe and see you soon.
Brett
« Last Edit: August 29, 2012, 12:39:52 PM by bretto »
Brett Orem, UT� [size=14]PHOTO DIARY OF MY BUILD[/size][/URL]

Offline Carls_jeep

  • Flatfender Master
  • *****
  • Posts: 1746
  • Karma: +0/-0
  • ...
    • View Profile
Re: Annabel's ready
« Reply #5 on: August 29, 2012, 03:36:11 PM »
The way it's looking I will try to make it a two day trip. I may get in Blanding late Friday night. It all depends on how much driving time I want to spend.