The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - locomotive2111

Pages: [1]
1
Buy, Sell, Trade / Re: Air cleaner to carb hose
« on: May 25, 2023, 07:11:37 PM »
found this on Early cj5 site

2
Has anyone used the M38 gas pedal and cross shaft assembly to  replace the civilian cj2a and 3a and 3b. It seems to be a little better design where the pedal connects to the cross shaft.  I need to replace my cross shaft or weld it since it broke at the weld on the cross shaft  where the gas pedal link attaches to it

3
Hi everyone, I was having an unusual misfire condition and after much  research and study  I found the answer. The problem was caused by worn distributor shaft bushings which caused the points dwell to vary greatly . Dwell of course is the time the points are closed which relates both to timing which affects idle  and coil saturation or voltage at the plugs. Here is a web site that really explains it better. www.howacarworks.com/ignition-system/checking-the-dwell-angle. I know you can avoid this problem with a conversion to electronic ignition but us purists like points. I spoke to a race car builder who explained the need to maintain the distributor to get peak performance. Good luck and keep on Jeepin.

4
I am confused about the location and number of dowel pins on the main bearings. I had my block machined and they disappeared when they cleaned the block. Some manuals show 5 pins and some show 6. The parts suppliers sell them and say you need only 5. Ok but where do they go There are 6 bearings, 3 mains upper and lower. Am I missing something and if not which bearing half does not need one.

5
Gearboxes and axles / Re: front axle shaft and steering knuckle lube
« on: January 10, 2021, 11:16:50 AM »
I am still doing research on the front axle closed knuckle lube.  As a rebuild mechanic in the Army I repaired hundreds of these on 2 1/2 and 5 ton trucks. Replacing the boots was a never ending job plus greasing the joints was no picnic. I just found a place that sells a grease for this very purpose. It is called Torque King 4x4 and the grease they sell comes in a caulking tube and costs $8.00 for a 16 ounce tube.  I did email Dana and asked them for any engineering data that was used in this design. On 2 1/2 and 5 ton trucks the king pins are lubed with a zerk fitting so that part of the joint is not concerned with splash lubrication from the joint.

6
A short time after putting my 53  3B back on the road I noticed a weird sound coming from the dash area. Since I had already replaced the speedo cable I checked out the speedometer assembly. Many old units can be easily disassembled to service them but this one could not. But, it can be lubed by a small hole on the rear of it. I oiled it with 3 in 1 oil and now  it is quiet . I guess this is one more item that needs service  on a  50+ year old vehicle.

7
Announcements / wheel rim id tag
« on: August 17, 2020, 10:38:34 PM »
I just removed what appeared to be an original spare from my 53 cb in preparation for new tires and found this original kelsey hayes id tag . Just thought it would interest some. here is the picture of it

8
EVERYTHING ELSE, General tips / Re: Lug nut opening - Overtightened
« on: June 26, 2020, 03:40:55 PM »
I have seen these rim holes fixed by welding them to build the metal up then redrill  the hole most small machine shops could do this in one or all 5 of the holes

9
Engine compartment / Re: Firewall Clearance
« on: June 10, 2020, 07:40:03 PM »
I am not  sure what clearance is or should be but make darn sure the accelerator linkage is properly aligned on the back of the block .If it is not installed pointing in the right direction you can not hook up the rod to the carburetor and accelerator pedal and is a major pain to change without moving the engine or the body.

10
Engine compartment / oil indicator level cap gasket
« on: June 10, 2020, 07:32:54 PM »
After much research on this subject to improve tightness of cap and improving pcv system I discovered the original gasket on the cap was leather backed by a brass piece like spring. I placed another thin gasket between the brass and leather to make up for the worn leather thickness . This worked great. A Felpro 5019 bowl gasket could be used in a pinch if the leather is lost or damaged but could be slightly sanded to decrease its thickness.  Unlike the leather the cork gasket would not wear as well where you constantly check your oil level.  Some small aircraft use a similar system and use silicone gaskets like part # 08-13773 at Aircraftspruce.com to seal the dipstick tube. For your info the gasket is 2 1/4 o.d. and 1 i.d.1/2

Pages: [1]