The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - RA472A

Pages: [1]
1
"Original"-- Technical Questions, Answers, Observations / Re: Flywheel
« on: November 05, 2011, 09:33:40 AM »
Be careful  when bolting the pressure plate to the flywheel as the torque specs only about 17lb.  

2
If it looks old, or you don't know when it was last serviced, I'd definitely replace them.

3
I'm with Mike.  The oven cleaner and putty knife system works fine,but takes time and space to do it.  For $40 or so I think you can have it done at a local machine shop and be done with it. the rebuild is not difficult, but takes time.  When I started tinkering, I didn't know a camshaft from a hole in the ground.  i think I've done a dozen trannys last count and learned something new on every one. I second everyones sugggestions on finding NOS parts.  One of the things I will put on the MUST replace after the last two rebuilds is the entire synchro hub and clutch sleeve.  Tried to scrimp on a couple for some buddies and cost us a do over in each case.  Get a copy of Rick Stivers rebuild guide which is an invaluable resource. He still doesn't get enough credit for that piece of information, in my opinion.  Take your time, do it right and you'll be very satisfied.

4
Sounds like it could be a vacuum leak also.  Make sure carb is tightened down with a good gasket under it.

5
Try jacking up one front wheel at a time and see if you can rock the tire side to side or up and down.  Could just be loose wheel bearings.  I've had that happen for fear of overtightening and burning up bearings.

6
I found the specs for the IAD 4008.  The endplay is .003-.010 as measured with feeler gauge between the lower thrust washer and the base of distributor.  Manual says if too much gap, add thrust washer. Drive shaft bearings(1/2' bushings) should be replaced  if side play is over .005".  After taking a couple apart and tinkering, they really are fairly simple, but kinda tedious to rebuild correctly.  My 3A was running like crap, no matter what I fiddeled with.  So I finallly just swapped out distributors and it made a huge difference in being able to get timing correct. I had one rebuilt by a fella named Don Hall in Oregon a few years ago.  Beautiful job and I think it was around $125, so I'm sure they are more now.  I thought his son was taking over, but I kind of lost track.

7
If you need to replace the bushings, Ron F. on the g503 has rebuild kits that include bushings and new springs for the weights.  The wear is measured with a feeler gauge at the collar where the thrust washer is.  Measure this before you tear it all apart.  If it's within tolerance, just a good cleaning and lube may be all you need as already mentioned.  I believe if the gap is over .011 then bushings should be replaced but don't quote me on thaqt until I verify.

8
"Original"-- Technical Questions, Answers, Observations / Re: Bumpers
« on: February 09, 2011, 12:08:46 AM »
The easiest thing may be to use grade 8 cap screws.  You can fill them in with a quick weld and grind to resemble a rivet.  A good hardware store will have them.

9
The three screws you removed should allow the brake drum to come off IF the brakes are not hanging up.  Once the brake drum is off, you need a spindle socket to remove the spindle lock nut.  There will be a flat washer tab that is holding the outer lock nut in place and that will need to be bent down flat again to allow the spindle socket on.  from there, you should be able to see the washer, another lock nut, and then another washer that rides against the wheel bearing. all must be removed before removing the six bolts that holds the brake backing plate on.  Do you have a good manual?  Really helps for the step by step stuff from there on.

10
"Original"-- Technical Questions, Answers, Observations / Re: Tires
« on: January 31, 2011, 10:18:18 AM »
Personally, I like the 7:00x16 since it is stock and gives you another inch of clearance or so.  As far as snow, I don't like them, but they are great on everything else.  I prefer the stronger sidewall on a bias tire for dingin' around on the trails.

11
I've redone two sets of rims and I've always painted the entire rim, inside and out.  Never had any issues and it's been several years now.  However, I use tubed NDTs.

12
You can slip the ball end of the park brake cable out of the handle under the dash. You still need to undo the cable from the clamp on the engine firewall.�For the steering wheel, find a bearing seperator (cheapo Harbor Freight) and clamp it just below the wheel and then you can put your puller arms on the steel clamp. �Remember to put the steering wheel nut back on and put a stack of washers between the point of the puller and the nut so you don't crush it. �Leave the nut a little loose so the steering wheel has room to budge. �Repeat gradually until wheel off.

13
If it's turning over that slowly, I'd replace the condenser before I got into an expensive starter swap.  That's why mine was doing also.  You can also try to tweak your distributor just a bit to see if it helps starting.  Never underestimate the power of NEW spark plugs either.  Once they get fouled, I'd replace.  Just my $.02

14
Just another suggestion.  Piano wire is stiff enough to work well when fishing up the horn wire also.  Costs a couple bucks, but handy to have around.  I also made my windshield latch spring out of it.

15
Rambling, Malarky, Rants, Etc... / Re: Doors on a Jeep
« on: December 05, 2010, 11:53:28 AM »
You may be interested in seeing how I set mine up with half doors.  They work great for keeping the cold draft from climbing up your back when the weather turns cold and still have great visibility which is what the jeep experience is all about for me.  Added another couple months to the jeep season for me in the PNW.  I can send you some pics if you're interested.  PM me when you get time.

Pages: [1]