The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Ranger41

Pages: [1] 2
1
Chassis, brakes and suspension. / Installing M38 Leaf Springs on 3A
« on: July 16, 2022, 03:08:33 PM »
Hi all,
I'm getting around to replacing the rear leaf springs on my 3A and decided to use NOS, M38 springs.  I've read the previous discussions about the merits and drawbacks of these springs and have opted for them because my 3A is a working Willys and I haul loads in it under less-than-ideal road conditions.  I also want the reliability, over the long haul, of well-tempered American steel from nearly 70 years ago.   

Two Questions:
1) I've pressed out the steel sleeved rubber bushing on the forward pivot eye and replaced it with the bronze bushing to accept the 3A/2A greaseable bolt.  The OD on the bronze bushing was a little less than the ID of the spring eye.  I've made up the difference for a snug fit by wrapping the bushing in thin sheet metal, but it's not my first choice.  Are M38 spring eyes different ID than CJ's or do these bronze bushings vary in OD?  I saw one supplier that offered a steel sleeved bronze bushing for 2A/3A's (can't find it right now for reference).

2) On the aft end of the spring the ID of the spring eye is .013 smaller than the "C" shackle bearing - the bearing is approx. 7/8".  The shackle bearing is such a tight fit, I can't get it in far enough to engage with the threads on the shackle.   I've thought of reaming the spring eye, but I don't want to go taking away material that I can't replace - and that steel will be really hard to ream.  I've also thought of slamming the bearing in with a hammer, to get it in far enough to engage with the shackle threads - but I wanted to see what the Forum wisdom is on this before I start whaling on things.  I've also consulted M38 TM 9-8012 and the Willys Manual and haven't found any satisfactory answers.

To top it all off, there seems to be a shortage of "C" shackles - Suppliers seem to be out.  I'm using some take-offs I had in my Willys spare parts pile.  I believe the shackle bushing is an original, since the end is recessed, so I think I can rule out bad foreign machining on on repops.

2
Hi,
If there's still one if those five available I would like to get one too.  Just PM me with the details.  Thanks for meeting the need for a part like this.  The vent on mine has been sealed up as long as I have had it.  Would be nice to make it functional again.
John

3
Bob,

Thanks for the thought regarding the CJ5.  I had not thought of that possibility.  I'll see what I can come up with on CJ5 frame dimensions  and Meyer Plows. 

4
Thanks for the photos Lee.  Not sure what type you have there, but it is an interesting design that seems to transfer the force from the front of the frame to along nearly the whole length.

The Meyer Plow frame only connects to the front 1/4 of the Willys frame.  Still puzzled about the clearance on that aft connection point. 

I'm still learning about this jeep. I just discovered in June it has an Willys MB engine, then today, I just noticed it has the motor mount adapter to allow the MB engine to attach to the CJ3A frame.  I guess that one of the fun things about old Willys - Always something to discover!

5
Hi all,
Well after being reunited with my CJ3A after 4 years, I'm trying to figure out how to attach the Meyers snow plow rig I picked up a few years back.  The frame supports seem to line up nicely with holes in the jeep's frame EXCEPT......  the rear attachment points are off by 1/2 inch.  This seems to be due to a flange/tab on the rear of the plow frame assembly bumping into the aft, front leaf spring mount.  I could cut off the rear 1/2 inch of that tab on the plow frame, but before I break out the cut-off wheel and make it fit I'd like to see what other CJ3A owners with plows have to say about their set-ups.  Pictures of your plow frame set-ups would be appreciated.  Mine is a Meyer ST-72 with the Electrolift Hydraulics.  First Photo is the front of the frame, second is overview of trouble spot in the rear, and third is a close-up with the front, aft leaf spring mount and the plow frame flange.  The plow frame is the shiny POR15 pieces of steel.

6
WOW!  This is perfect.  Thanks so much for the details and photos.  That 3A looks great.  Did you add the tool inserts to the tub?

John

7
I'm considering placing an M38 top on my CJ3A - not militarizing it - I just prefer the look and function.  Can anyone steer me towards measurements for the placement of the bow brackets along the body sides?  Thanks.

JB

8
Thanks.  That section of Vern's site was very helpful.  I've gotten some great tips from his sites before, but did not think to look there for the spindle info.

9
OK, I'm replacing my front right axel spindle because the wheel bearing surface was pitted with rust and no longer true to round. �I have an old 3A frame and axels in our yard (much to my wife's displeasure) - and I thought ah-ha! �I can just pull off the spindle from this one and use it on my complete 3A - my own personal junk yard. �The spindles look the same and they both have the bronze flanged bushing on them. �The bushing on the replacement spindle looks OK but I thought I'd replace it anyway while I had it apart. �The replacement spindle came from a �Bendix axel, and the one it's going onto has Rezzepa axles

Two questions: First - I looked up the bronze flanged spindle bushing on the Wlacks site, it specifies that it this part is for Rezeppa and spicer axels only. �was there a difference in the bushings on the 3A bendix vs rezeppa? �They look the same.

Second, how do you get the old bushing out, and seat the new bushing? �t looks like a bushing puller with a slide hammer/side facing grips would be able to pull out the old one and I could tap the new on in place, however I'm thinking about letting a machine shop do it. �Thoughts?

Thanks

10
That's the image I was looking for.  Thanks!

11
I'm in the process of installing a M38 rear tailgate spare tire carrier on my 3A.  I recall seeing a diagram on a website a while back that had the proper measurements for the bolt holes in the tailgate, but I can't seem to find it anymore.  Does anyone recall seeing this and can you send the link, or if not, have some recommendations for hole placement?  Thanks.

12
Thanks for the response.  I have the diagram and the manual, and have new wiring harnesses 80% installed.  The diagram for the 3A http://www.cj3a.info/tech/Elecpart.html   shows the ignition switch, but no additional relay or solenoid on the starter circuit.  It puzzles me because every other model from 2A's to 3B's and early CJ5's have a solenoid or starter relay.

13
I'm in the process of rewiring my 1950 3A (the old bubba wiring went up in a wisp of smoke).  At some point in the past someone installed a starter relay on the firewall and had a push button start. I'm trying to take it back to original and putting in all new harnesses and a 3 post keyed switch.  My question is, the wiring diagrams show wire running from the Ammeter post to the starter post and the pos. battery cable running right the starter post, with no relay or switch in between.  Does that sound right?  I know the 3A's a had a few different starting configurations: floor plunger, keyed, etc. Any photos of 3A starter wiring would be much appreciated,  Thanks - JB

14
Thanks.  I'll put this information to use.

15
I'm in the process of replacing the windshield on my CJ3A. �It may have been replaced before. �The windshield gasket has a thinner piece of rubber inset into it to lock the larger gasket it in place. �When I removed my old one, this smaller inset gasket was on the front (outside). �I've come across some indiction that this inset strip of rubber is suppose to be inside (facing the driver). �It seems to make sense for it to be facing the driver, and out of the weather, so I'm questioning how it was arranged when I took it apart. �Thoughts?

Also, any guidance on replacing the windshield would be appreciated. �I've seen some info on using a cord to hold the gasket in place. �Thanks.

Pages: [1] 2