The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - SteveV

Pages: [1]
1
"Original"-- Technical Questions, Answers, Observations / Re: Fuel Pump
« on: September 19, 2016, 05:10:00 PM »
Will do, Coming in tomorrow.  Putting it in and will update.  ::fingers crossed::

2
"Original"-- Technical Questions, Answers, Observations / Re: Fuel Pump
« on: September 19, 2016, 04:01:51 PM »
Anyone have any experience putting a electronic conversion in? Like the one below...

https://www.amazon.com/PerTronix-1541-Ignitor-Prestolite-Cylinder/dp/B000N2XOQC

3
"Original"-- Technical Questions, Answers, Observations / Re: Fuel Pump
« on: September 19, 2016, 11:50:57 AM »
Thanks Ronnie & Tim for the feedback.� I did change over to 12v. Bought the kit on eBay and seems to be OK.

This is the conversion kit I purchased---
http://www.ebay.com/itm/Jeep-Willys-6-Volt-to-12-Volt-Alternator-Conversion-kit-Deluxe-/272354651611

Quote
I replaced the coil with a internal ballast one and changed my condensor.

Do you remember what part numbers you used for the coil and condenser?

I think you are right on with the problem I am having.� ::Crossing Fingers::

4
"Original"-- Technical Questions, Answers, Observations / Fuel Pump
« on: September 15, 2016, 06:09:04 PM »
I purchased an Omix Ada fuel pump for my CJ 3A and I don't think it's working well.� The bowl barely fills up.� �The car will shut down within 15 minutes of driving.� No bogging down or anything, it just shuts down.� She will start back up about 5 minutes after sitting.� I don't think it is vapor-lock.

Is there a better fuel pump I should put on the Willys?� I think this is my problem.

This is the pump I put on...
https://www.amazon.com/gp/product/B000FQ0EN2/

5
Small update....  Finally getting back to putting together the 3A.  Some issues, but so far, so good....Still deciding on Seats.  I might just pounce on these and make brackets.  Any have aftermarket seats that they made brackets for??

https://www.amazon.com/Rugged-Ridge-13400-01-Standard-Black/dp/B001FAGKQC

Short video---


https://instagram.com/p/BHKLYtUhIFW

6
Here is the progress on the cover.  Not quite finished but seems to be going good. 

The fenders seem to line up with the grill & hood.  ::crossing fingers::

Only drawback with doing this & not moving the body is the rear goes past the frame a little bit. (as another member has pointed out)


7
Specialty, Thanks  I will be in touch on the seats. 

Today was good progress, was too busy for pictures, i will post some tomorrow.

Kirk Nice BOX!  Gave me a neckache checking it out but worth it.    Yellow wouldn't be my preference, more of a green.  The body was painted when I bought it a couple weeks ago.  I'm certainly not complaining, it's growing on me. 

macrisel Thanks for the info on the trans cover.  Mine ended up getting cut up today, I will post pictures tomorrow.  I also need to put shims the trans mount a bit more so the trans lays a little lower.  Someone had bolted down the body and the trans bent the body a little from hitting.


8
Quote
You could also just get some rectangular tubing  the same overall size(height and width)  as the hat channel and weld it to the hat channel flush with new mounting holes to move it forward and it would be good as new after painting the short pieces.

I like it.  I will post pictures tomorrow of exactly what's going on and my thoughts on it.
I got the fenders and grill mounted this afternoon with no problems. A little flexing but everything seemed to line up well.

CJ Pilot, It looks like I am heading in that direction temporarily.  BUT I'd hate to cut the cover, thinking maybe a step-up.  We'll see in the next few days.

9
Quote
push the tub forward to its correct position

Hi Ryan, thanks for the info.

Reason for adjusting body -- Trans Cover, rear of body extends past frame, fender lineup.� I can deal with the body extending past the frame at this point.� If I really want to correct it, it will be later.� For now I will fabricate something for the transmission cover for the shifter.� there seems to be plenty of room for the steering column.� I bought the Jeep last week... still learning about these.

In all reality, I will have to cut some of the body to bring the body forward about 1.5".� I thought about drilling the frame mounts and seeing if that will provide me with enough room.� Would be tight.� Before I go cutting the body or the body mounts, I am going to get the car together and go from there.�

Not bad to do it all over again. 8-)

10
Quote
I could be completely wrong here but if that is a repo body I�d bet it was painted before it was extensively reworked in order to fit properly on the frame.  If that is the case it�s going to take some tweaking to get everything to line up.

I'm not sure where this body came from or who made it.  The owner was so confident that it is original, "found it in a junkyard"....but I don't think so.  He may have found a repro in the j/y!  He included pictures of it before he painted it.  It was black.

It looks like I will have to re-work the body.  As the above poster, athawk, noticed the rear isn't flush. 

11
Quote
the back of your tub looks like it's sitting about an inch rearward of the rear bumper/crossmember.� The crossmember and the rear wall of the tub should be nearly flush.� If you can shift the tub forward, your shift tower issue will probably go away.� Of course, this may cause mounting issues with the front fenders and body mounts.� Have you tried to lineup the fenders yet?

Thanks!� Great mention on the body in the back & fenders.� Makes my gears go a little smoother thinking the body has to be moved forward.� I haven't mocked up the fenders yet, but I am sure that they will be off considering the rest of the body.

EDIT--- I got the fenders, grill support, & hood on today and they bolted up OK.  I spoke to Jay @ WILLYS-OVERLAND today and he said this is a common problem on repro bodies.  They "tweak" the holes in the body to make it come forward about 1.5-2".  Considering my fenders and stuff lined up, I am going to fabricate something or modify the trans cover to make it fit.  The rear of the body is in fact hanging a little bit, but I can handle that for now. 

12
[size=14]I recently bought this 3A.� Putting it together one by one.� Got her idling today which is good.� Also, the Jeepsterman is only 20 minutes away for parts.� Big bonus.

I am pretty sure the body is reproduction, it's just too nice.� Not 100% sure though.� A major problem i have is the cover for the transmission on the body. (as pictured)� I removed the body a handful of times, check Engine & Trans Mounts.... It does not mount correct at all, about 1" off.� Anyone have these problems?� Hopefully it's the wrong cover?[/size]





[size=16]I am also looking to purchase seats.�
Something like these....
http://www.amazon.com/Smittybilt-44801-Black-Back-Seat/dp/B001CF1V3C

Does anyone have any experience buying aftermarket seats?� Advice?

Here is the rest of the car....[/size]







13
Once You've Joined / Re: New Member, NJ
« on: January 06, 2016, 07:18:42 PM »
[/img]

14
Once You've Joined / New Member, NJ
« on: January 06, 2016, 07:18:17 PM »
Browsing around this seems to be the perfect 3A forum.  Just using the search I found a lot of info on the build of my 3A. 
 
I do have a few questions which I will post in a different section.

Thanks in advance, Steve V

Pages: [1]