The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - danorte

Pages: [1] 2
1
Carlsjeep. Just to clarify. I can drive out the bushing and the dorman plug from the starter side, out the backside of the bell housing? there is no ridge or shoulder to hold the bushing from going to far when inserted?? If so then carefully drive in new bushing till flush with inner aspect of bell housing ?? Thank you again. North

2
Thank you all so much. Will try the tap and pull method as soon as I can get it in to the barn. Again my thanks. North

3
Thank you Carlsjeep. will try this next weekend. It feels like the starter bendix is hitting on the face of the flywheel. Solid chunk when pushing the starter pedal. No engagment. If I rotate the engine by hand it will sometimes engage. No marks on fly wheel and no other abnormalities I could see. Will replace the bushing and let you know what happens. Thank you again. North

4
Good after noon all. My 1950 cj3a foot pedal starter hits against the fly wheel. New starter and fly wheel at rebuild. I did not at the time replace the bushing in the bellhousing that supports the nose, shaft of the starter. I have read the list, about replacing it with engine out. Has anyone replaced this bushing with the starter out and the engine in. I read there is a plug at the back of the bellhousing that is press fit but can the bushing be driven out the back of the bell houseing???? along with the dorman plug???? Help. I really need the jeep but facing pulling the motor to replace this one small part is frustrating. What say you all jeepeers. help. North

5
Welding gas tanks is dangerous, however I have welded one following cleaning and then filling with water. Weldiing the full tank gives less chance of explosion of the vapors which may be left in the tank. So positioning the tank with filler neck at the highest point, fill with water to highest level making sure filler neck is cleaner than clean, ie no smell of fuel. Weld carefully. I am not sure I would do it again due to extreme stress on my heart during the welding procedure. Waiting not so much for fire folks, rather emt to bring me back. I only did it outside with plenty of room and a friend to call 911. I have seen one explode that the fellow said he had cleaned really well but he tried to weld it empty. Big mistake. It unfolded in the explosion and though did not break any bones he had the most bruising on his legs and thighs. Not telling you to do it just be very very careful of the explosive fumes. Norte

6
I vote rope seal. I used one in my rebuild and no leaking yet? I used a broom stick handle to roll the seal into the groove prior to crank install. Worked very well for me. As a note with many older rebuilds of various makes. rope works well. north

7
I too used steel line to replace the hose and it fractured within 4 hours of use. Went back to rubber line. Not sure if I did preload adjust, however with oil flying everywhere under the hood a mile from the ranch made me change the hose. I do believe the vibration from the engine fractured it. I recommend the rubber hose. North

8
Morning, I agree the best is transmission mixed with acetone. However second best I belive is PB blaster and a tincture of time. Spray all over valve stem and guide and wait a day, spray again and wait. Tapping on the valve head works but very large danger of tilting, bending the valve head. Not worriesome if you are going to replace the valves anyway. If valve is stuck and you do not want to hit it then use some heat,  torch, or hairdryer to heat up the valve guide and usually it will free up the frozen part. Remember lots of flammable stuff to set on fire so extinguisher at the ready. Let us know how you are doing. North

9
Good afternoon. Well after a lot of searching I found 7.00x15 ndcc tires at summit for 90.00$ per tire. Shipping was 32.00$ very happy. I know most of you run 16" but my 1950 cj3a came with the 15 on it. Farm jeep so 7.00x15. Cannot wait not to get stuck in mud and snow. North

10
Thank you all, will recheck this weekend to see if load, drain or other abnormalities. North

11
No, three wire following Doug's pictoral. Meter on the battery shows, 14+ charging volts. Now you all have got me thinking even more so will recheck all this weekend if the snow doesn't show. North

12
Thanks carlsjeep. When this jeep sits for a while it takes a bit to start it up in the winter. Up in the forest it did not start right away after being run for 1 hr. The battery is new, alternator is new and charging fine. However after 3 tries it seems the battery was drained. Hiked out to hiway and good samaritan drove into woods and gave me a jump. Started right up. Hence my diagnosis pointed to starter. I have all new cables. This weekend will check all over again, if the weather is ok. Thanks again. North

13
OK, new plugs, new engine, new rebuilt carb x 2. Not issues. issue is starter. minus 11 here so not using at this time. I have had many old vehicles and have had starters develope severe resistance when they got hot from the engine heat. I do understand the 10- 30 sec rule. So will see if local can rebuild mine. Thanks for all the info. North

14
Thank you all. I guess what I am saying is with old starter coils they need much more electicity to start when the starter is warm by eitherthe motor or by starting the jeep. If my jeep does not start right away and I do not try more than the 30 sec rule then on occaision it will drain the new battery. Happened way back in the forest, so just want to avoid it in the future by rebuild. I did find rebuilt starter 6vlt from Walcks for 199.00 and for an additional 25.00 they would upgrade to 12 v. Anyone done this?? thanks again. North

15
Good afternoon, does anyone have a place to have a 6volt starter rebuilt to 12 volts. I know I can use the 6 volt but the age of the starter means when hot it may not turn over the motor. So I want to either rebuild it or have it rebuilt. I have found no parts for it that any one has. I did find the contacts on the starter at a web site but they did not have it afterall. So... needing starter stuff. North

Pages: [1] 2