The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - dat

Pages: [1] 2 3 ... 7
1
"Original"-- Technical Questions, Answers, Observations / Re: Fuse?
« on: April 30, 2015, 01:49:04 PM »
Quote
Hi Nate,

It's an original switch...and I'm sure it was just the resistor burning off some crud....

but if it had been more serious, then the only way to break the circuit is to jump out, open the hood, and disconnect the battery..I never did get that battery disconnect switch installed, i couldn't find an under-dash location that didn't require lots of extra battery cable or cutting holes....


looks like a fuse on the back of that switch,   I don't have a heater on mine so I don't know, but from the picture it looks like a fuse

2
Quote
it's not too hard...


visually my intermediate gear looked fine but was noisy....the used replacement gear is quiet.....



just a thought, new gears, may be not exactly smooth teeth, doesn't hurt bot could be noisy,� could it quieten down with time, wear in.   more as a question for future reference for me than as a solution to anything mentioned above

3
Quote

I've found that there are almost ALWAYS trans/TC and axles left as they seem to be the last things to rot out....everyone has them and I literally have a shed full that I can't give away. Smaller stuff is easier to sell as it can be shipped.



and I'm in need of the axles/ differentials, but like you said, the shipping is the expensive part

4
around here, that would be worth looking at, not many sitting around here and what there is is getting expensive, folks would want 1500 to 2 k each, just sitting in the weeds like that.   still not saying it's a good deal, but sure worth looking at. 

5
Quote
You may also want to check the yoke itself and make sure it does not have a groove worn it it.� If it does, bite the bullet and buy a Speedi-Sleeve for it also.� If you don't fix it now, you will probably still have a leak (been there, done that� ::) )

how far worn will a speedi sleeve work on?  my yokes are worn well into, not just visible but worn into an hourglass, was looking at new yokes but had forgotten about sleeves, been 25 years since I've used one

6
but fun, the body on mine is pretty much junk, but once I get all the pieces put back together, mechanically it'll be a fun ride again, something that I never minded if I bounced off a tree and kept on going.    now years down the road if I ever do a body restore, that would change. 
cheaper than one of those big razors or ranger and a lot more classy

7
Quote
This sucks. I'm about to drop it off somewhere get it running and put a for sale sign on it

don't give up, you're still making progress even if you don't think so,   but if you're selling, How cheap ??   ;)

8
if stuck in, the clutch disk should be free,  but it could be stuck either the pressure plate or flywheel,

9
they won't move untill the throwout bearing puts pressure on them, you won't be able to mash them in by hand

10
you can see some through the inspection cover on the bell housing

11
it may seem simple, but is the clutch fork on the pivot and in the throwout bearing housing?

12
I'm ready to hear that thing crank up

13
mine is and is registered as a 48 cj2a  I just happen to have a lot of 50 cj3a scrap parts on it, like body, frame, engine etc.

14
are you saying that your vin and title don't match   :o

 ;D

15
really not bad, costs more than just a blank plate, but comes stamped with original type script stamps, with original type mounting rivets and shipping for 48.70 and I don't get a chance to mess up the stamping

Pages: [1] 2 3 ... 7