Messages

1

"Original"-- Technical Questions, Answers, Observations / Re: windshield doesn�t rest

« on: June 17, 2013, 11:48:01 AM »

Thank you Tim, your pictures really sample the corrections to make, greetings.

2

"Original"-- Technical Questions, Answers, Observations / Re: windshield doesn�t rest

« on: June 16, 2013, 11:28:09 PM »

If they are right, the motor is not the original, it is one new that have just bought in kaiserwillys, I had already thought of cut the cleaner's offspring a little, but it is not a lot what one can make, in a same way, I already proved to remove the motor totally and even so it doesn't seat the windshield in the blocks, for the information that gave me 3A Guru, I should make blocks more big, I would like them to confirm me the measures that  he has given me.

3

"Original"-- Technical Questions, Answers, Observations / Re: windshield doesn�t rest

« on: June 16, 2013, 09:40:46 PM »

Ok, maybe, I try to take a new pictures whit low resolution, I hope is better, bue thanks again and excuse me for that.

4

"Original"-- Technical Questions, Answers, Observations / Re: windshield doesn�t rest

« on: June 16, 2013, 09:33:06 PM »

Thanks, for the datail, and sorry for the pictures sizes, I am not sure how can do.

5

"Original"-- Technical Questions, Answers, Observations / Re: windshield doesn�t rest

« on: June 16, 2013, 09:12:49 PM »

Here is the pictures:

6

"Original"-- Technical Questions, Answers, Observations / Re: windshield doesn�t rest

« on: June 16, 2013, 09:04:03 PM »

Hello, again bothering, this day I takes him some pictures to my CJ3A and I could check measures of the wooden blocks and their location, I go up the pictures so that you can appreciate it, the dimensions of the blocks that I have are 11.2x3.8x4 centimeters of high, both are located at the same distance of the hood center (33 cm) and to 3.5 centimeters of the hood edge, I understand that starting from the CJ3A this is therefore the wipers they already go located in the low part from the windshield contrary to the previous models where were up and for that reason it was necessary to put the blocks at different distances, I also find that the blocks of the CJ3A are more high that those of the other ones, I will thank a lot if somebody can give me a small drawing with the correct dimensions for the CJ3A, it could send this way them to make since I know a good carpenter, I wait their comments, greetings.

7

"Original"-- Technical Questions, Answers, Observations / Re: windshield doesn�t rest

« on: June 16, 2013, 12:52:03 AM »

It doesn't seem to be bent and when I bend it the first part that it rest over the hood it is the part of the ventilation window, then it cannot bend more, not yet I have a picture that shows it, but I have found this in the forum where it show a willys to which doesn't rest the windshield the same as to mine.

8

"Original"-- Technical Questions, Answers, Observations / Re: windshield doesn�t rest

« on: June 15, 2013, 08:49:52 PM »

This are some pictures of my Willys

9

"Original"-- Technical Questions, Answers, Observations / windshield doesn�t rest

« on: June 13, 2013, 09:06:55 PM »

 I have a consultation, is the case that my CJ3A of 1950 when bending the windshield doesn't rest� over the wooden supports that are in the hood and don't I understand why, somebody would can to give me some idea?

Edit by Admin
I've re-sized all the pics in this thread to 800 wide so they can be seen by everybody. Also made the file size much smaller for those on dial-up. Hope this helps.

10

"Original"-- Technical Questions, Answers, Observations / Re: Hood blocks

« on: June 16, 2013, 09:27:08 PM »

I also have to make sure the passenger wiper is flipped all the way to he right. If I leave it flipped left with the windshield down it will make contact with the hood and scratch it. My hood is a little goofy so not sure if that's an issue with all 3A's or just mine.

Hello, I have the same problem exactly, the dimensions of the blocks that I have are 11.2x3.8x4 centimeters of high, both are located at the same distance of the boss's center (33 cm) and to 3.5 centimeters of the boss's bank, I understand that starting from the CJ3A this is therefore the cleaners they already go located in the low part from the windshield to diferncia of the previous models where were up and for that reason it was necessary to put the tacos at different distances, I also find that the tacos of the CJ3A are but high that those of the other ones, I will thank a lot if somebody can give me a small drawing with the correct dimensions for the CJ3A, it could send this way them to make since I know a good carpenter, I wait their comments, greetings.

11

Once You've Joined / Re: New from El Salvador

« on: June 13, 2013, 08:57:55 PM »

Please excuse the size and the resolution of my pictures, I am still trying to learn how to go up pictures with the appropriate size, greetings.

12

Once You've Joined / Re: New from El Salvador

« on: June 13, 2013, 08:43:15 PM »

Hi, I post some pictures of my toys, I hope you like it.

13

Once You've Joined / New from El Salvador

« on: June 12, 2013, 02:44:08 PM »

Hello my name is Carlos, I�m from El Salvador in Central America, I like a lot 4x4 experience, I have a Jeep CJ7 1984 and a Willys CJ3A 1950, I hope to contribute and to learn much of all, thank you to give me the opportunity to belong to this forum, greetings.