The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Ryan_289

Pages: [1] 2 3 4
1
I went to the parts store today at lunch and picked up a spare set of points and condenser and was talking to the old man about it.� He said that since my coil was an internal resisted coil that it would be on the hot side.� Said as long as I could keep my hands on it to not worry about it.

I would still be curious as to what others are seeing.  Next time I drive it I will shoot it with my thermometer and check temps.

2
I had an issue a several days ago.  My jeep started running rough and I started checking wires and the ignition coil was hot to the touch.  I purchased a new one and it was still running rough so we changed the condenser and that seems to have fixed my running issue.  2 nights ago we drove the jeep around for around 30 minutes or so and when I got back I felt of the new coil and its still getting hot.  Its mounted to the block, do you think it could be getting heat from their?  Everything seems to be running right, I just didnt think ignition coils were supposed to get hot like that.  Does anyone elses coil get hot?

3
Others may chime in but that one doesnt look good enough to dress up.  I see some teeth with chunks out of them.

4
Jim did you get a body kit?  The oddball looking bent cowl seal that came with my kit was crap.  I got one of the better ones from Ron Fitzpatrick.  I had my old windshield frame to compare but I centered mine and drilled and screwed from the center out to keep it tight.  I did have to trim some of the ends down so the windshield would clear the cowl when closed.

5
Quote
Linda .... The threaded part is in the hanger.� If it is not usable, the hanger will need to be replaced.�

Replacing the hangers is an interesting task as you need to learn to install rivets which is a new skill for most of us.�

I used grade 8 bolts and nuts to reinstall mine.  I figure with that and the 1" long welds on all 4 corners they weren't going anywhere.

6
I had to move the seat rest pieces on the wheel well up on both sides of my repop tub.  I cant remember now if I drilled a hole for the drivers seat back there.  Its at the body shop getting paint now so I cant look and see.  I also had to heat and bend my front tubes of the seats to get the back to sit down properly.

7
My tub is at the body shop but it looks like I forgot to drill the hole in the cowl brace for the sending unit wire as well.  What do I need to do to prevent rust where I drill the holes?

My replacement tub was built in February 2015.  The pto shifter hole was there, high beam indicator hole, fuel hole, pedal holes, and all gauges. 

Problem was the gauge holes were too small, the fuel tank holes were in the wrong location, and the brake pedal hole was off >:(  Nothing a welder and a burr bit cant fix but dang its frustrating.

8
I would resurface it if it were mine.  Around here its not very expensive to have it done.

9
I tried Multi Luber in mine first which is a pourable grease sold by John Deere.  It still leaked a little with that so I used a syringe and pumped it full of corn head grease.  Its good stuff.

10
You might check with the machine shop and see how much it would be to hot tank the motor.  It will get the insides completley cleaned out.

11
I resleeved one on my 48 that I messed up.  I ended up finding an NOS rear yoke on ebay that worked great. 

12
Mine isnt on the road yet but im running John Deere 30w oil.  Its rated for older diesel engines so it should have zinc in it.

14
I may have a good intake at the shop.  If I remember correctly it had some broken bolts in it and would need machined on the mating surface.  If I still have it your welcome to it. 

15
Thats what they are for.� I had the same thing left over in a seal kit that I bought from Walcks.� I called Carl and thats what he told me they were for.� I think I reused the ones that were already there.

Pages: [1] 2 3 4