The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ZekeD

Pages: [1] 2 3 ... 15
1
Gearboxes and axles / Re: Koenig 51 single stick pto
« on: September 08, 2020, 11:35:23 AM »
It came that way.......    the box was stiff and someone strong armed it I think.     Shifts much better now

2
Gearboxes and axles / Koenig 51 single stick pto
« on: September 07, 2020, 08:57:55 PM »
Can you heat treat a Koenig 51 pto shifter?     My single stick fork looks more like a “Y” than a “U”.   I am reluctant to bend it back to shape more than once.   Can I heat it and then quench.?   Are there any single sticks for sale?

Thanks
Zeke

3
Gearboxes and axles / Re: Koenig 51 transfer case
« on: February 24, 2020, 11:56:08 AM »
Thanks I didn’t see any reason for the packing.        Nuf said

4
Gearboxes and axles / Koenig 51 transfer case
« on: February 23, 2020, 03:06:21 PM »
Help.   I am putting my 49 Cj3a back together and I have gotten to the Koenig box.   There are 5 “special bolts” that connect the aluminum case to the transmission.     When I went to clean them up it appears that the lock washers have packing around them.    The packing looks like water pump packing from my model A.   The lock washers are knurled on their outside face.   Since the Koenig is splash lubed from the transmission anyway, what is going on?

Any facts/opinions are welcome

Zeke Duge


Ps. This is one special bolt / washer,  and a second disassembled washer.

5
Cool!  If you built a jig, could you make all of the bends at one time with only one heating?

Just 2�....  ;)

Zeke

6
Thanks, guys!

My real problem was that I was trying to remove the whole assembly.  After carefully re-reading the advice I see that only the end needs to be removed.

Problem solved.   
Regards
ZekeD

7
Guys,

I have locking hubs on the front two wheels.  They are the non-warn type, you know I have the ones with the two levers.   I have removed the six bolts and the lock mech seperated from the front hub, but not by much
(1/4 in?). Can I just pull on the lock?  How much force should I have to use?

Am I going about this wrong?

Thanks
Zeke

8
Just because I don't know:  what is the significance of gasket/ no gasket?

Thanks
ZekeD  :-/

9
That's it.....     Thanks for the help

10
On the passengers side of the rear engine support ( #18 in fig. 52  of the parts list pg 96) is a support/insulator which I think is  part A-914.

Does anyone have a pic of this beast, or know where to buy a good one? Or if I am wrong, er, oh, grump,mumble what is it that goes into the hole in #18?


Thanks

Zeke

11
As always the humor is often as enlightening as the facts....  Thanks everyone,  it was the leak issue that I was trying to circumvent.   So I put it back into the frame hooked it up and it did not leak for now.......

Regards
Zeke

12
Thanks, gents!    I like the simplicity of Squidtone's and the flexibility of Birddog7's.    What to do. What to do?    Think about it over a beer, I guess.

Zeke

13
Right..... A great but outta my reach idea.   There are not so many pieces here in central Oregon to cut up, and it is very BIG.    I need something smaller, you know space is cubic when you are trying to heat it!
 :D :D :D

Thanks
Zeke

14
Does anyone have plans for an engine test stand?  I have looked for the one that Squidtone made with no luck.    Just going to use it once ( ok, right... Never mind).  But do not want to put a lot of $$$$$ into it.

Thanks, guys

Zeke Duge

15
"Original"-- Technical Questions, Answers, Observations / Re: 3A and 3B
« on: February 04, 2015, 08:00:27 PM »
There were a lot of "short people" jokes hidden in there.......    Grump grump

Zeke.   5'6" or sumpthin'

Pages: [1] 2 3 ... 15