The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Operation Overlord

Pages: [1] 2
1
PAST EVENTS: / Colorado Fall Colors Tour 2015
« on: August 04, 2015, 12:18:09 AM »
Fall colors tour in Colorado has been posted on CJ2A page. See link below.

http://www.thecj2apage.com/forums/fall-colors-tours-2015_topic34106_page1.html

2
Anybody seen one of these handles?  Saw it on an Ewillys post. Its attached to windshield.  What does it do?

3
Well, sounds like i have some work yet. I want to get it to fire up much faster. I'll try and post a video of it starting in the next couple of days. See what y'all think.

4
Yes, using choke.

5
"Original"-- Technical Questions, Answers, Observations / Starting
« on: July 13, 2014, 04:54:29 AM »
How long does it take your Jeep to start? I have a 6 volt 3A that after sitting for a week or two takes a long time to crank up. I'm talking 3 to 4 cranking iterations of 5-10 seconds each, sometimes longer.�

I have a fresh Walcks Carter that I replaced recently hoping to fix the problem. Fuel pump is new too as is entire fuel system. Feels like fuel in carb is evaporating or draining while sitting. Or maybe it's normal. I don't know. I've only seen one other Willys start. That was a 12v 2a with electronic distributor. Fires up nearly instantly.� Oh, I static timed the engine using flywheel marks as well. Same result.

6
My 49 has the oil filter mounted this way too.� Correct me if I'm wrong, but somewhere I read that owners moved them there to accomodate frontal hydraulic accesories. My 3a came from Minnesota where I think it was used to plow snow with a hydraulic type setup.

7
I like the custom bracket set up.  Will look at that solution.  Thanks for the help. 

8
Does anyone have any cool ways to mount rear license plate?  I took my Jeep for some really light off roading and already dinged up my antique rear plate.  As is, it hangs down real low with no real protection. 



9
I was in the process of bolting on the exhaust manifold when a stud broke. I decided to drill out the broken stud and thats about the time I realized that the studs go directly into the water jacket. It was so frustrating that I could only laugh.�


10
Here is a link to my Photo Bucket album with some paint and body pictures.

http://s1282.photobucket.com/user/RealOpOverlord/embed/slideshow/Paint%20and%20Body

The Monstaliner covers a lot of bad body work but I'm doing a rolling restoration and it works for what it is at this stage of my build.� On a side note, all the reasons for using bedliner are� all the same reasons to avoid buying a Jeep that has it bed lined unless you go into it knowing that it could be pretty ugly underneath.�

11
It depends on what result you want. The body on my 49 is terrible.� Hugh Bondo patches mixed in with Metal pieces over original rust areas.� I even have rivets on the outside panels for some reason.� I just wanted one color that could be applied cheaply at home so I used roll on Monstaliner in Blood Red.�

Having said that, I really like the result.� It has an orange peel texture that is smooth and it hides a lot of the flaws.� When I do end up either fixing or replacing the tub I would consider using it again.� Resell value doesn't bother me as I don't plan on ever selling it.� The plus side is I don't have to be gentle with it in the garage or worry about scratches.�


12
Yeah I didn't order the screw kit since I didn't know I needed it.  Do you think the Home Depot route would be OK or should I just wait and order it from Beachwood?

13
So I just got my Beachwood Canvas seats in today and realized the upper seat cushions have to be screwed through the canvas to the outer tubing.

Any suggestions or advice before I go about doing this?


14
"Original"-- Technical Questions, Answers, Observations / Re: Shop Stuff
« on: February 02, 2013, 09:54:20 PM »
Yeah I think i'm going to hold off for now.  I like the idea of dropping parts at an old shop.  That would probably be easier and less to worry about.

15
"Original"-- Technical Questions, Answers, Observations / Shop Stuff
« on: January 28, 2013, 09:14:53 PM »
So I am in the process of repairing the brakes on my 3A.  I've currently been using a combination of brake cleaner, wire wheel, and wire brush to scrape off all the old dirt and grease before I coat the parts with paint and reassemble.  I've been seriously considering a parts washer to help out.  Is it worth it money and sacrificed garage space or should I just keep trucking and spend the money on parts instead?

Pages: [1] 2