The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - 52withaGPW

Pages: [1] 2
1
Thanks for the input and pics, Tim. I honestly don't know the exact model of steering box I have in my 3A, but it looks a lot like yours. It's most likely a Ross. All I know is, mine is about 3 turns away from being completely useless. I haven't been taking out of city limits for months now. Half a turn of play in the steering wheel, easily, and all the adjustment is taken up.


How hard are the boxes to remove? I need to rebuild mine, badly.


Kit.

2
I've often wondered if the steering box in my 3A was the right one. Outside of knowing how to adjust the slack out of it, I really don't know much about it.

Is it supposed to have a grease zerk in the top of the case, or was that a mod someone did years ago? Just doesn't seem right to pump it full of grease. :o

3
Well, she's up and mobile once again. 8-) I was wrong. The float was sitting about 1/8" off.

4
For the last week or so, I've been unable to run my 3A. Starts just fine, but the carb absolutely pours fuel out. I've had it apart several times, checked everything out, and I can't seem to find out the root cause. The float sits at the proper level, hasn't sunk, and doesn't have any holes in it. Needles and jets check out just fine. I haven't let it sit long enough to build up any varnish or anything like that.

Is there some type of check valve inside that I'm not seeing, that keeps fuel coming in full-pressure if it's out of spec? Should I just tear it all the way down and rebuild it? I don't believe it's ever been rebuilt.

I'm honestly out of ideas here, guys. I could sure use some help.  :-[

5
Rambling, Malarky, Rants, Etc... / Re: roads on BLM lands
« on: September 06, 2012, 12:16:50 PM »
I guess I'll take the fine then. ;)

6
Rambling, Malarky, Rants, Etc... / Re: Stealerships
« on: August 28, 2012, 01:00:39 AM »
A buddy of mine recently had the gasket and seal, on the oil pan fitting of his '97 Powerstroke blow out. Blew oil everywhere. It's that funky little fitting that the dipstick tube presses into.

Called the local Ford dealership, and they quoted him $1700, and a day's work, to replace the fitting and seals. Claimed that they would have to pull the engine to drop the pan out (which I can understand. Not enough clearance to drop it down far enough, and the crossmember is riveted to the frame).

Turns out all you need is the $20 gasket and seal kit, as well as a $2.50 .45 caliber cleaning brush and cleaning rod, to hold the fitting in place so you can install the new o-ring and gasket. ;D

7
Quote
I did a very good job as it does look like a real M1919. What kind of finish did you put on it?


If I remember right, it was flat black Krylon. I really went el cheapo on it. I'm going to go over it with my airbrush, and highlight most of the high points in a dull silver color, so it looks like it's got a bit of wear and tear on it from use.

8
Quote
It think it is superb, however, you may need to edit the "Bone stock 1952 CJ3A." heading near your avatar �;D


This is true. ;)


I had a bunch of scrap laying around that was too nice to just junk, so I thought what the heck, I'll make something cool. The only real part on it is the barrel, and it's plugged and welded in several places. The rest is just scrap. Didn't have a torch at the time, so I cut most of the parts out with my Dremel tool and those easily-broken cutoff wheels. I guess I do have patience after all. ;)

9
Rambling, Malarky, Rants, Etc... / How do you think this will look?....
« on: August 10, 2012, 02:05:46 AM »
when it's mounted in the back of my 3A? Been working on it off and on for a year and a half now. :) ;) 8-)



10
Rambling, Malarky, Rants, Etc... / Re: On the road again..
« on: July 31, 2012, 01:21:16 PM »
Quote
Quote
Top pic looks like the area around Helena, and Townsend, MT.



We have a winner!! � �Highway 200 I believe..
Makes me want to go up there in the winter and do some skiiing or boarding...

One of the other pics has a very obvious clue...



I thought it looked familiar. I was over at Canyon Ferry with a buddy a while back, walleye fishing. Saw quite a few Jeeps while we were there, including at least one 3A in downtown Helena. 8-)

11
Rambling, Malarky, Rants, Etc... / Re: On the road again..
« on: July 31, 2012, 01:39:28 AM »
Top pic looks like the area around Helena, and Townsend, MT.

12
Rambling, Malarky, Rants, Etc... / Re: Jay Leno Jeep Quiz
« on: July 24, 2012, 06:02:37 PM »
1485. ;D

13
Your CJ-3A Project / Re: Just a few pics of my 3A.
« on: August 21, 2012, 12:06:36 PM »
Quote
That is a fine looking Willys! 8-) �Whatcha got hiding under that canvas in the front? �I'd trade you a couple headlight rings for whatever it is. ;)

What heater? �Is it a Harrison?

Tim

By the way, I've got a [size=16]49withaGPW[/size]



That was a Tulsa pto winch. Sold it a few days ago to fund a new rifle project. When I first took it off, I discovered that it had, over the years, ripped the first foot or so of the lower part of the frame wide open. No wonder the front end wanders a lot!

The canvas was an old radio cover I picked up at a gun show for $5 a couple years ago. Made a pretty handy dust cover.

I'm not sure what brand the heater is. The core was leaking like a sieve, so I took the whole works out. I'll have to get a couple pics of it, so someone can help me identify it.

14
Your CJ-3A Project / Re: Just a few pics of my 3A.
« on: August 12, 2012, 12:17:09 PM »
Quote
Nice Jeep - and especially cool that you use it as a "daily driver". What's that valve and hose on the top of the motor near the firewall? Mine just has a plug there. Is that for a heater or something?


Yeah, that was for the heater. There's one on the water pump as well.

15
Your CJ-3A Project / Just a few pics of my 3A.
« on: August 12, 2012, 12:56:30 AM »
Not much of a story to tell about this old girl, I guess. ;) I'd been wanting an old flatfender for years, after hearing all kinds of stories about them from Grandpa. He used to talk about how much fun he had in the couple he owned years ago. Stories of climbing so steep you couldn't see anything but blue sky past the hood, or coming down a hill so steep you almost had to stand on the dashboard.

That stuff just fascinated me for so long, I knew I had to own one someday.

Fast forward around 20 years or so. An acquaintance of mine had owned this 3A since the late 1970's. He was the second owner. I talked to him about it every time I ran into him around town, especially the gas station.

I pestered him all the time about selling it to me. He'd just laugh, and tell me "if I do decide to sell it, you've got first crack at it". Honestly, I think he was just trying to shut me up. ;D

I had built the engine in my Ranchero up enough, and ran it around enough, that I finally got bored with it, and put it up for sale. Sold it on a Friday afternoon. Later that day, I take a walk across town, wallet in tow, to check in on the Jeep. Knocked on the shop door, and the gentleman told me to come in.

I asked him if he was still thinking about selling the Jeep. He told me "yeah, I suppose I could, why?" I whip 22 $100 bills out of my wallet, and ask "well, do you take cash?" :D

Sold! Drove the ol' girl home shortly thereafter. Drove it almost every day for a year, and by that time, the 'ol L134 was getting pretty tired. Most minor grades I'd have to take in 1st or 2nd gear. No power at all in 3rd.

I tore the engine out, rebuilt it, and here's what I ended up with :). Two and a half years now since the rebuild, and she's still going strong. I drive it almost every day. I'll never get tired of it, that's for sure.

The fenders, tub, windshield frame, frame, axles, basically everything but the engine itself is all original from the day it rolled off the line in 1952. A few minor items aren't original (like the Nissan air cleaner, which has since been replace by an original oil-bath unit), but I'm pretty happy with it as it sits now.

Whaddaya think? :)






Pages: [1] 2