The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Redrockman

Pages: [1] 2
1
"Original"-- Technical Questions, Answers, Observations / Re: Shop Stuff
« on: February 01, 2013, 09:50:42 PM »
I have found washing parts with Kerosene has a plus, they don't rust like many other cleaners, due to a thin film of oil left on the washed parts.

When i finally get around to the washed parts after ordering repair parts, finding the money for the same and going on to other items while waiting, very rarely do i find surface rust!!!

The vapors wont cause an explosive mixture settling to the floor just waiting..........

My .02 cents

Redrockman

2
I have been viewing these posts for a while, and seeing how my jeep is in a holding pattern i haven't motivated my self too much.......

Did get a visit from Calvin just before Xmas and thanks again "Calvin" for the visit, as to the motor in the pictures it looks like it has been steam cleaned. If the cleaning was VERY recent then it probably is alright. The other side of the coin is if it was done a while back please ask him to get 2 complete revolutions out of the motor and also ask him to pull the plugs and take a photo of them.

I have had bad experiences with steamed cleaned motors seizing up due to too much time from cleaning till getting it ready to do something with.

My 2 cents worth........

Redrockman

3
Looks like you have over 1/2 of the hole there, my suggestion is to get a grade 8/"AN" washer and trim it to fit the casting before you put the bolt/lock washer back in the case.

"AN" washers are the same thickness for better load under the bolt head when you torque the bolt, it can also be welded using a carbon arc rod in the hole for a temporary plug while welding it using a Stainless Steel welding rod on an aluminum plate, then all you do is knock out the carbon plug and chase the hole with a drill bit.


My .02 worth'

Redrockman

4
What type of rings did you use, and did you check end gap clearance on the rings before installing them?

Did you reuse the old rod bearings too, or were replacements installed?

A few places to start checking, for if you "oiled" the new rings before installing them and put lube on the bearings then it might be a little stiff yet should turn over A OK.

Good luck, keep us posted

Redrockman

5
I lost a motor due to silicone/RTV getting into oil passages and clogging oil feed lines, so you may want to check if the RTV made it into the bearings or the internal side of the engine.

The oil pump was contaminated by bits of RTV that got into the "relief" side of the pump and i'm sure it would have caused issues......

Better safe than sorry,

My 2cts worth.

Redrockman

6
This is not a hard fix, today's specialty welding rods work wonders!!!!!

Take a bolt of the same size and coat it with carbon from an oxy/act torch that is only burning the fuel, no oxygen. That will coat the bolt and you can then screw the bolt into the hole. Then you can weld right over the broken part and you will have built up enough metal to replace what was lost.

If by chance the bolt will not unscrew after the repair, cut the bolt almost flush and drill and tap the bolt out. Use a soft bolt one with no marks on the head of the bolt, DO NOT USE GRADE 8 BOLTS............

That's how i repair cracked cases at my shop, cast iron, aluminum, it's the same process.

Redrockman

7
Don't forget the old standby, oven cleaner the $1 store kind not the expensive stuff!!!! Found this stuff years ago for use as a degreaser in a pinch......... ::) ::) ::)

8
It's been a while since i last posted. Lost living arraignment, job, had major surgery and to top that off Jeep is in a storage place.

Glad to hear that the damage was confined to only a few lost teeth ;D. I'd like to comment on using RTV as a sealant, i've lost a few motors in the past from tiny bits of RTV clogging oil passages that came loose from use. So all i'm saying is to be very careful on how much you apply. That said i switched over to Permatex 2 non hardening or Hylomar for internal sealants.

Always good to hear a Willys driver over coming those nagging little details thrown in the path of life!!!

"Just like a Willys in 4wd" � Greatful Dead

9
That's some fantastic work there, are you planning to undercoat it too? have been figuring out if i want to undercoat then paint to protect it or try some of that rubberize coating then paint.

Seems like the best work comes out of a garage........... � ;) ;) ;)


Andy

10
"Original"-- Technical Questions, Answers, Observations / Re: Engine swap?
« on: September 01, 2011, 10:55:39 PM »
Thanks guys for the great tips on installing falcon carb.

�2 questions, throttle linkage and did you need to adjust internals on carb? by that i mean re jet, or metering rod change, cuz not sure of internals with this carb....

Will do the Rock auto thing......... Again thanks for the tips/photo's   ;) ;D ;D

Andy

11
I will not ruin a CJ3A nor will alter it's appearance.........Where do you get a side draft carb? cuz to me aCJ3B is ugly :o figured i'd ask about engine swap a friend has a good running motor he will let me have. So back to the side draft carb, whats up with the linkage for one of those?

Any suggestions welcome,

Andy

12
I have a 51 CJ3A and have been offered a "F" head motor that runs fine. What do i need to do for it to fit in my jeep?

Andy �[smiley=beer.gif] [smiley=beer.gif]

13
If i'm not mistaken here on the windshield gasket orientation, the locking strip goes outwards as in facing out not in. Reason in the event the vehicle gets into a major impact the glass will eject outwards not in your lap!!!

Used to install auto glass, and that's what i was told, years ago............. hey maybe i got it bass ackwards ;) ;) ;)

14
If i remember correctly the inner is larger than the outer, that said you can remove/replace bearing cups with out going to the machine shop.

Clean hubs and get all the grease out of the backs of the bearing cups, you should see 2 little notches in the casting that you can see the edges of the cups. Using a long punch(longer is better) pound out the cups a little at a time on each side of the edge of the cups. When you have the cup out, grind down the outer dia. of the "old" cup (cool in water as you go they get hot!) enough so it can easily slide back into hub.

Now you have the cup driver as a tool to  insert the new cups with, no need to lube new one, place old cup on top of new cup matching narrow edge to narrow  edge and drive away. look on back side of hub and you will see when cup has bottomed out.

A larger chisel laid across the race being tapped helps even out the force needed to re insert new cup helping to prevent "*" of cup and saving fingers too  ::)

The money saved you already spent on the next part of the jeep to be "worked" on, unless you need to visit somebody anyways. If so kindly disregard my rambling on..............

15
"Original"-- Technical Questions, Answers, Observations / Re: Brakes
« on: August 10, 2011, 03:23:04 PM »
Thanks for the info, and that sure makes me feel better about upgrading system. Didn't want to do the "disc" thing, will look mostly stock and STOP!!! Kinda like having cake/ice cream and enjoying both ;D ;D ;D

Thanks.....

Pages: [1] 2