The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Toms1951

Pages: [1]
1
Engine compartment / Re: Engine block crack
« on: January 25, 2026, 11:36:58 AM »
Thanks Russ.  I’m not a member of that forum, but I sure do read it a lot.  The #4 sleeve just isn’t constrained it the down direction.  I see it being the only reason that it moved down.

I suppose I should see about registering on the other site.

2
Engine compartment / Re: Engine block crack
« on: January 24, 2026, 11:34:30 PM »
A mosquito fogger. Yeah, that’s pretty funny considering we live on the Milk River in Montana that is noted for its huge mosquito populations except in winter when it is -40 degF.

I’ve spent a few thousand dollars on this L-134 engine re-conditioning having 4 standard sleeves installed, all new valve seats cut in, and mostly new valve train parts installed.  Now that I’ve stripped down to the block for the second time, my theory is that the #4 sleeve had slipped down about down .005 after the first run.  I say this because I know the deck was machined flat at the start.  There are cutter marks across both the deck and all the sleeves (#1 thru #3 are perfect), and no good machinist would leave a sleeve 5 thousandths below a deck height.  Moreover, the #4 sleeve doesn’t bottom out on a step as it should and was bored through.  This is from a repair during prior ownership.

I’ve included a photo showing cylinder #3 and #4 juxtaposed to show #4 position was bored through at one time for the prior sleeve installation.  Note how the sleeve bottom is exposed.

The engine is jinxed.  I can only think the #4 sleeve will have to be pinned somehow or have some dowel through the sleeve to hold it in place.  I can’t shave the block any more than it has been, which probably means another new sleeve and any required crack repair.

My jeep is really nice.  It is all stock, unadulterated, and a rust-free original vehicle.  I really wanted the L-134, but now I’m contemplating engine swap and have been reading quite a bit on it.  Either the Kubota V2203 or Ford Ranger OHC I4 with Novak the adapter.  I think that it would be far less frustrating, especially trying to repair this one, find a replacement block somewhere, or buy a new block from a vendor.

3
Engine compartment / Re: Engine block crack
« on: December 09, 2025, 09:23:08 AM »
I'd been using the jeep regularly of the ranch without issue, so I drove to town.  It is about 3 miles at 45 mph.  When I started the engine again at the gas station after filling it up, a huge plume of steam came out.  It was repeatable at the post office and grocery store, so this little experiment failed.  Mark W. is right about (re) decking the block.  The sealing interface between the head and block needs to be perfect or it just won't hold - especially at high power settings.  I think we all probably know this.

Dang man, I was just bragging about how great a jeep is over a side-by-side for work around here. 


4
Engine compartment / Re: Engine block crack
« on: December 01, 2025, 05:40:20 AM »
Best copper gasket installed.  Ran it on about a 20 minute drive.  Retorque completed next day.  Waiting for -20degF to stop before more driving.  So far it’s held.

5
Engine compartment / Re: Engine block crack
« on: November 18, 2025, 11:21:04 AM »
Thank you for the responses.

Both the head and block were decked.  The head is about .001" in flatness.  A visual inspection of both surfaces were performed visually - more than once prior to assembly.  It's funny, I use Plastigage on the main and rod journals prior to assembly but ignored checking the flatness of the block and head prior to assembly (or even a surface dye pen). It was because surfaces looked so pristine upon receipt.

I know some don't like the copper gaskets at all, which is reinforced by comments in other forums.  My rationale for the copper gasket is that it may be mailable enough to form over the block inconsistencies; especially if I can get a really good evenly distributed clamping force with the head fasteners across the interface to prevent any gapping.  I will retorque once after the first thermal cycle.

Fixing that crack and re-decking the block is the best solution.  I just got the damn thing together though, and it was running so well.  I'm just not wanting to pull the block and all internal components for machining yet.

The small missing chip that creates a small pocket has a bottom to it.  I don't think there is a water space cast under it.

Lastly, it looks to me like this sleeve installation caused the localized failure during installation, which is the crack initiation and propagation, the missing "chip" between 3 and 4, and the .005" under height of the sleeve.  Unfortunately, I missed it. Thus, the lesson learned: Always check level first - even maybe a quick dye pen. 

6
Engine compartment / Re: Engine block crack
« on: November 15, 2025, 09:05:53 PM »
I meant to re-torque after the first and some subsequent runs not retire….


7
Engine compartment / Engine block crack
« on: November 15, 2025, 07:44:52 PM »
After two years and a move 1600 miles to NE Montana, I finally completed my CJ3A go devil engine.  About two hours into running I started getting steam into the exhaust plume and had a pretty good flow of a water mix coming out the muffler’s small low point drain hole at shut down.  Very dishearten, I decided to pull the head. The engine was bored and sleeved back to standard size. I used the Felpro 7285B gasket with 5 studs under the removable oil filter  and air tube brackets and bolts for the remainder of the fasteners.  I  torqued the head down in three steps. I’ve attached the photos that show a crack, between number 3 and 4.  I believe this is the path for coolant into the combustion chamber of number 4.

The machinist supposedly leak checked it after machining and has a good reputation for working on classic motors. He is also 1600 miles away in West Texas. 

I can only think that lock and stitch will fix this permanently, but the sleeve is adjacent to it.  I also found the sleeve is .005 inches below the head surface.  Shown in the second photo, which I believe is another issue

I have some money into this motor, so for now I will attempt a Best copper gasket, all studs for assembly, and lubricant on threads and a retire after the first couple of runs.  Hopeful to stop the leak. 

Open to any other suggestions.

8
Engine compartment / Hasting Rings
« on: June 14, 2025, 09:38:11 PM »
I was reconditioning an L134 and during the new Hastings ring installation, standard size, I noticed a manufacturing defect in the ring.  The number two. I attached a picture.  Would anyone use this ring?

 Well I decided not to.  It may not be an airplane engine, but I just did t want to risk a failure.  I ordered a new single piston set.  Didn’t bother with a return. 

9
Engine compartment / Re: Engine oil pickup assembly
« on: May 17, 2025, 11:53:03 PM »
Yeah I just can’t figure out that string.

10
Engine compartment / Engine oil pickup assembly
« on: May 08, 2025, 11:12:18 PM »
Took this apart though it was rinsed really well in the solvent tank.  Including photo.  There also seems to be a cotton string gasket wedged into the flange.

11
Engine compartment / Re: Engine Serial Number
« on: May 14, 2023, 11:09:14 AM »
Bob,

You're exactly right, she's been rode hard and put away wet.

engine makes power, and antifreeze in the radiator seems to go down requiring refill.

Tom1951

12
Engine compartment / Re: Engine Serial Number
« on: April 29, 2023, 09:42:08 AM »
Also noting (and learning) a bolted head with an "industrial" wording cast in the head.  The jeep came with brush guards, rear PTO, and the extra curled front spring the drivers side.

Should have read up more about engines. Still a fun jeep.

13
Engine compartment / Re: Engine Serial Number
« on: April 27, 2023, 11:22:12 PM »
Ill get it this week-end,but it looks to be 641087 series and the rest needs solvent and a brush due to road grim.

unfortunately, It is not original.  Buyers beware. i think I've seen one Henry J in 60 years of my lifetime.  I wonder if hand stamps are from any mass rebuild of the early era for work order ID.

Also noted the #1 firing position is at a nominal 2 o'clock position. Dang man there are manuals.

Still fun and runs. What could I want?  Nothing.  Thank for respose.  More to come.

14
Engine compartment / Engine Serial Number
« on: April 26, 2023, 03:13:42 PM »
Can anyone make out what this ESN is on the attached photo?

15
Once You've Joined / Re: Welcome Toms1951
« on: April 25, 2023, 10:40:22 PM »
In 1972, I learned to drive in the hay fields in a CJ-3A with my Grandfather.
I owned a Willys 1951 pick-up from 1981 to 1990. That had a Dodge 230 flathead engine swap and a Warn overdrive.  I put a lot of work in it a would love to get it back.
I recently purchased an original CJ-3A with little surface rust, but sort of worn out, which I love.

451-GB1-10078

Pages: [1]