The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - iflylow74

Pages: [1] 2
1
I missed out on working at the old fashion small town gas stations but I do remember going to them with my dad when I was a kid.

There would always be a couple old men setting out front just shooting the breeze. Dad would buy me a coke from the old fashion coke machine with the little door on it. I remember one station had a 50 gallon barrel full of the old coke bottle lids accumulated over the years.

2
calvinhunt,

I would love some plans as well! On my budget, even $230 is a little pricey for me. Luckily, I have access to a welding shop at the technical school where I work. That may be a great project for the students to build!


3
Quote
Another option is a rear seat out of a Samari Samari (Sic). They are 36" wide, and flip and fold. Jim

Very cool! I didn't know that, thanks for the info! :)

4
Hi all!

I have a question about rear seats for the CJ3A. It seems like they are as scarce as hens teeth and expensive if you can find one.

Someone told me that a seat from an old school bus is a good fit. I remember as a kid one of the last seats in the back of a schoolbus was a little shorter than the rest. Has anyone heard of this or tried it?

I realize it wouldn't be stock and may even be considered "ghetto" but hey if it works it works!! ;)

5
Thanks for the plans calvin!!!

6
I've only used Walcks once but it was a smooth transaction. They are very knowledgeable. I used to use Kaiser Willys too but got burned once and will never go back.

7
Athawk11-
Thanks for the measurements. It looks like our parts are similar but a little different. Here are my measurements:
Cannister
        Height w/ lid= 8.5" (to the top of the bolt)
        Diameter= 5.25" (without lid)

Filter
        Height= 4.75"
        Diameter= 4 1/16 "

This filter I have is a Wix 51006 and it is too small but I made it work by sliding it up the center post in the cannister over the oil outlet holes. This filter was the closest I could find.  Just estimating it looks like my filter is a good 2"  too short for the cannister. Going to try to find a Wix 51010 today and see if it fits.

8
Quote
I've got the one with the four holes in the bracket on the back as well, it uses a NAPA 1010 filter. �Which happens to be the same filter canister set used on the Farmall B and the Massey Harris 22, both made in about 1948-50. �If your out in Farm country or near it you should be able to find these in inventory at NAPA. �If not try Wix 51010 its the same filter.

Awesome!!! Thanks gunslinger!! I had a sneaky feeling that my filter cannister was from a tractor. The person I bought it from on ebay said it was for a Willys but oh well, as long as it works.

Luckily, I live smack dab in the middle of farm country so surely I will be able to find the correct filter. Thank you for the part numbers!!!

9
That would be great athawk11! That would allow me to figure out if my cannister is a "standard" size or not. Mine looks like yours but without the two straps holding it.

I've got the motor ready to start for the first time but hate to start it without a filter so I've been itching to find one pretty bad!  :)

10
Hi all,

I have a question about the original style  oil filter cannisters for the CJ3A. When I bought my jeep, a previous owner had removed the oil filter assembly so I bought one off ebay.

I didn't know much about jeeps when I bought it. Looking at pictures of original cannisters I can see that mine is different. The original ones appear to have two metal straps that connect the cannister to the engine mounting bracket.

My cannister doesn't have that. Instead, it has a flange on the back of it with four bolt holes. I had a friend make a custom bracket to mount it to the engine but I can see that the original style bracket wouldn't work with my cannister.

I'm not too worried about it not being original but it does call into question what kind of filter I need to buy. I purchased a filter from Oreilly's auto that kinda worked but it was too short.

Does anyone have the dimensions of the original filter/cannister so I can compare to mine?

11
Very cool, thanks for the link!!

12
Hey all,

Finally have my new crank/bearings installed and am on to install the flywheel and clutch. This is all new to me so I'm learning as I go. :)

Any tips on aligning the clutch? I've seen special tools used for this but hate to purchase one if not completely necessary as I will probably never use it again.

Thanks!

13
I am finishing up the new crank/bearings installation in my 3A and am having some trouble understanding how to set the crank endplay.

I've read over a post on crank endplay at the CJ3B website but am still not completely understanding what to do. Heres the link to that forum:

http://www.film.queensu.ca/CJ3B/Engine/Rebuild5.html

One problem is that everything I read about it assumes the pistons are out of the engine but mine are in the engine and that makes it hard to get the crank in place.

Any tips or tricks for a Willys newbie??   :)

14
Quote
My sweet wife volunteered to help me drop the motor into the frame tommorow night, I think she might be angling for a ride to the DQ!!! ::)

Opps, she just said Ben and Jerry's!!! Spendy date 8-)

Sounds like a fair trade to me!! Good luck getting the motor in, let us know how it goes!

15
Sounds like a good plan gunslinger! I think I remember reading about the same procedure you mentioned. One guy recommender after pulling the plugs out to pour a little Marvels Miracle Oil down each spark plug hole to lubricate the pistons.

Not sure about that but I guess it couldn't hurt anything! I can't wait to get my Jeep back into one place and give it a test drive.

Pages: [1] 2