The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - johnnybravo

Pages: [1] 2 3 ... 5
1
When correct, it should charge at 6.2-3 volts.

2
I have talked with jpet and last time (about six weeks ago)he did not have M38 top information.  As far as I know, the M606 (the model for military CJ3B) is the same.  Check the The CJ3B Page, several guys hang out there from you continent, maybe your country. 

3
The tailgate on M38 was only bolted shut when not in use. The spare tire carrier on M38 is two piece. The top can be removed and relocated to passenger side like the CJ3A. If you look at passenger side of OE M38 tub you will see four dimples for locating the tire carrier holes.� We used our M38 tailgates on a regular basis to draw ammo, carry heavy weapons and etc.� move tire carrier and tire to side, strap can somewhere, strap top back panel to forward bow and use straps in lieu of chains. You can make the change pretty quick.

As I pointed out earlier, your jeep appears to be M38. From the the photo your tub and frame have M38 features.

4
Did the info work?

5
gg, When you ask for length do you mean from bottom of socket, up one side, across top, down the other side to bottom of socket. If you will PM your email I can send you pics from smarter than me phone with dems.

6
SteveZ,
I learned a long time ago do not mess with that plug.  It has been dragged over everything you can think of and most likely pressed the threads into something unlike a spiral. Now I just remover the cover to drain, if it starts to be stubborn. I have wasted a lot of my life on the $&?! things!  Once, I had to remove the axle and turn it down side up, to remove the plug I had drilled through.

7
Thanks David, I was thinking you had some special wires other than what I could get at Auto Parts store.  Although, I am looking to find the best carbon wire I can get. 

8
Ok David, where can you get them, what do I ask for?
I believe you but do not know where to go from here.

9
...or drive shaft revolves 5.38 times to one revolution of the wheel.

Aahhhh,
...43 divided by 8 equals 5.375 and rounded up, equals 5.38

10
Lunette comes from wagons. I believe the lunette was on end of the stave pole. I was in antique shop before Christmas and owner had a table of free stuff if you identify, I got the lunette. I would post a photo but I have equipment down. If your want to see, send me a PM and I can send pic from iPhone.

...and French sounds correct.

...stave pole equates to trailer tonque

11
Maybe buy a frame to get all the OE stuff if you want original jeep. Has you front cross member been cut?  A little bit of anything between that U-joint and frame could
lock your steering. Could you post pics of the rest of the steering system?

12
ROCKETEER, YOU ARE CORRECT, BUT WHEN YOU DON'T HAVE INSULATION YOU SHOULD DO SOMETHING TO REDUCE/DISSIPATE THE HEAT BEFORE IT DESTROYS CRITICAL ITEMS.  THIS IS ONLY A BAND-AID AND I SHOULD HAVE SAID SO.  INSULATION IS BEST BUT IF YOU DO NOT HAVE, WHAT IS THE NEXT BEST THING?  IN OUR HOBBY JEEP WORLD WE HAVE TIME TO GET THE CORRECT RESOURCES AND DO THE JOB PROPERLY.

13
No insulating material.  You can drill three or four holes and screw 1/4" metal screws to act as diffusers or cooling fins/post.  I have done this on heat shields on underground mining equipment.  Works quite well.  

14
this begs the question...Whay did they eliminate the slots?  I noticed that last night while cleaning the drums for the 3B.

15
"Original"-- Technical Questions, Answers, Observations / Re: Vibration
« on: January 21, 2012, 08:36:52 PM »
THE TACK WELD ON THE DUST CAP ASSEMBLY COULD MAKE A VIBRATION AT CERTAIN SPEEDS.

Pages: [1] 2 3 ... 5