The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:
Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: tow hook
« on: July 08, 2022, 12:04:13 PM »

Quote from: farm1810 on June 18, 2022, 08:23:08 AM
I am responding to an older post on this subject, but chose to follow up on this one instead of creating a new one.  I purchased Herm's kit recognizing that there could be interference issues.  I actually cut out the cross member by the radiator and moved it.  Then realized the problem with the motor mount location as well (stock engine).  I believe this was designed for a CJ5 with V6 engine, not for a Jeep with a L or F head engine.  I finally abandoned the effort and move to an out front Saginaw arrangement.

 i got the kit as well, i did not use it either. with out removing any parts like a cross member/ or the engine plate that goes to the motor mounts . it's not bolt in with out some cutting. i rebuilt my ross box, wish it was better. but it's better then before thank heavens
Posted by: Marla.the.V35
« on: June 24, 2022, 01:24:03 AM »

Quote from: duffer on June 23, 2022, 10:45:38 PM
I'm another that just can't see any advantage of Herm's kit.  The Saginaw installation has no doubt been completed thousands of times on flatties, is both straight forward and well documented.

Coming from someone who considered it for a hot second, it's mostly appearances. All the benefits of a better steering setup, without affecting the outward look of the flattie. Also, if I recall correctly, it's touted as a mostly bolt-on system, so the appeal is there for someone who doesn't weld. (We all know how that goes with these old flatties though, nothing is that easy haha)

When it came time to pick a direction for my own steering, I decided to rebuild my steering box and replaced a few worn components. With quality parts, correct lubricants, and proper adjustments, it feels way tighter than I could've ever imagined it would, and I didn't have to do any modifications. Guys have got some horror stories about the ol' stock steering system, but don't believe 'em. When it's correctly maintained and setup to spec, it feels good and tight.
Posted by: duffer
« on: June 23, 2022, 10:45:38 PM »

I'm another that just can't see any advantage of Herm's kit.  The Saginaw installation has no doubt been completed thousands of times on flatties, is both straight forward and well documented.
Posted by: farm1810
« on: June 18, 2022, 08:23:08 AM »

I am responding to an older post on this subject, but chose to follow up on this one instead of creating a new one.  I purchased Herm's kit recognizing that there could be interference issues.  I actually cut out the cross member by the radiator and moved it.  Then realized the problem with the motor mount location as well (stock engine).  I believe this was designed for a CJ5 with V6 engine, not for a Jeep with a L or F head engine.  I finally abandoned the effort and move to an out front Saginaw arrangement. 
Posted by: Rus Curtis
« on: September 27, 2021, 12:58:54 PM »

Quote from: Ron on September 26, 2021, 11:18:46 PM
Good evening everyone,

I have been planning on using Herm’s Ford Reverse Steering kit on my CJ3B for awhile.  I got to the point of installing it today and found out that with the stock cross member, it will not be far enough forward so that the drag link lines up correctly.

Has anyone else used Herm’s kit on a 3B?

If I have to modify the cross member, I may just go with a manual Saginaw steering box.

Thoughts

RVSwisher



Ron,
With a quick search, I did find this post on Early CJ5 Forum talking specifically about this kit:
http://www.earlycj5.com/xf_cj5/index.php?threads/herms-power-steering.127681/

I haven't checked the links embedded but it seems there may be issues with interference.  I also noted that this may be a Saginaw but in reverse. 
Posted by: Ron
« on: September 26, 2021, 11:18:46 PM »

Good evening everyone,

I have been planning on using Herm’s Ford Reverse Steering kit on my CJ3B for awhile.  I got to the point of installing it today and found out that with the stock cross member, it will not be far enough forward so that the drag link lines up correctly.

Has anyone else used Herm’s kit on a 3B? 

If I have to modify the cross member, I may just go with a manual Saginaw steering box.

Thoughts

RVSwisher