The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:

Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: 1955CJ-5
« on: June 23, 2014, 07:19:04 PM »

Thanks Tim,

I probably should just get the original rebuilt...or do it myself....The originals are so much easier as they have a valve retainer that is screwed on, rather than the Airtex where the casing is distorted with a punch to hold the valves in....I still would have Hal do the diaphragms...

Something else to put on the list....

Randy
Posted by: athawk11
« on: June 23, 2014, 06:33:13 PM »

Hi Randy,
I installed an Airtex on the Whitey project.� I have the rebuild kit from the Classic Preservations folks.� I plan to rebuild the original, then install it on my OD Willys.� �Just not a huge priority right now.� By the way, thanks again for that link.

 The Airtex is a reasonably priced option for a decent backup.� It has the same vacuum and fuel hook ups as the original, so it would've pretty easy to install while in the field.� A single action pump would also work in a crunch, but you would also want to have provisions to close off your existing vacuum lines.�

I think it was just a bad run of luck on that FCT trip last year.� I believe it was Jpet that had two different pumps installed while on the same trail. Both were brand new after market single action pumps.� Crazy.

Tim
Posted by: 1955CJ-5
« on: June 23, 2014, 04:07:29 PM »

Hey Tim,

Have you done anything on the fuel pump yet?  I read your post in the High Altitude thread and am starting to think that a spare pump would be a good idea....but I suppose a parts store single action replacement would be a good enough backup....
Posted by: bretto
« on: May 11, 2014, 07:57:29 AM »

I got an Airtex over a year ago and can't say I have any problems with it.  I can't compare it to anything, but my M38 still moves forward.  I don't know about the performance of the vacuum function, I don't have a top and I don't feel like getting wet. :)

Oh bubba said, JB a weld will seal those holes up ;D
Posted by: 1955CJ-5
« on: May 07, 2014, 11:57:06 AM »

Good choice...once installed you probably won't be able to tell the Airtex from the AC...

When I did my pump, I found that the diaphragm removal(from the push rod) and re-install was probably THE most frustrating part of the entire restoration,after the windshield install of course...

Hal offers a service where you send in your old diaphragm and push-rod and he will install the new ones, out of your new rebuild kit.....IF your pump has the peened type diaphragm I would personally let Hal do it....if they are the nut-and-washer type then no problem....even a caveman could do it ;D
Posted by: athawk11
« on: May 06, 2014, 11:49:41 PM »

Thanks for the link Randy.
I did get a hold of Hal.  Decent price. $53.00 for a rebuild kit.  Made in the USA with parts that hold up the the alcohol rich fuels. 

I am going to get one and rebuild this pump, but it will end up on my OD Willys.  I picked up an Airtex reproduction pump for Whitey.  Looks pretty good, and seems to work well.

Tim
Posted by: 1955CJ-5
« on: May 03, 2014, 10:14:28 AM »

I agree...ruptured diaphragm.....I think it will also allow fuel into the oil pan....

or,

I understand that some of the AC pumps had the plunger fastened to the diaphragm with a nut and washer, others were peened.� Maybe the nut came loose and is allowing a little fuel to leak by? The top will come off pretty easily( 6 screws) for inspection..you might get lucky...

Kits available here...

http://www.classicpreservation.com/fuelpumpkits.html
Posted by: athawk11
« on: May 03, 2014, 09:22:34 AM »



This pump leaks fuel from the holes indicated with the blue arrow.� Some reading leads me to believe this has a ruptured diaphragm.

Looking for a consensus from the group.� Time to rebuild?� Or is this thing a gonner?

Tim

By the way, the thing pumps fuel like a grape ape, so I'm a little confused.