The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:

Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: 1955CJ-5
« on: June 12, 2014, 11:21:00 AM »

Thanks!

It was that first link that I was looking for..

Edit:  The instructions mention a spacer...I'll just find one that  fits......Thanks again..!
Posted by: Quebec Jeep
« on: June 12, 2014, 08:17:01 AM »

We updated the site last year and some path has changed.

You are looking for this one I thnik:

http://www.cj3apage.com/index/Tech_Tips/Original_side_step_instructions.htm

And there is also this one;

http://www.cj3apage.com/index/My_1950/installing_original_steps.htm
Posted by: 1955CJ-5
« on: June 11, 2014, 10:38:48 PM »

Here is that link..it doesn't work for me...

http://www.cj3apage.com/Original_side_step_instructions.htm

And here is the link to the 2a thread..

http://www.thecj2apage.com/forums/side-steps_topic27604.html
Posted by: 1955CJ-5
« on: June 11, 2014, 10:36:58 PM »

Well Bill, I have one...somehow I never think to look there first...page 102 on the reprint list

But, there is a spacer mentioned but no image in the diagram..
Posted by: F Bill
« on: June 11, 2014, 10:30:18 PM »

We have the how to install steps article, which has the CJ5 step[ mentioned, and there is also a link to the dealer letter and the diagram you posted a bit farther down the tech tips page... Chances are the link it dead as it went to the old website... If you think of it post a link to it so we can update the link back to here....I am not where I can access my parts books, but it is possible the parts listing may say what exactly the spacer is, if you can take a look at one.

Anyone got a CJ3A parts manual handy that can look for us?
Posted by: 1955CJ-5
« on: June 11, 2014, 10:30:15 PM »

The more I look at these and compare them to pictures on the web, the better they look.....

I'll need to clean them up and tack weld a couple of spots, and then some black paint.....

Ready to be ripped off at the first high-center opportunity :D
Posted by: 1955CJ-5
« on: June 11, 2014, 10:17:24 PM »

I found this over on the 2a page...there is a link to an updated set of instructions on the 3a page but the link goes nowhere...

My frame holes are already there as this jeep had steps, the remains of one came with the jeep but was pretty rusty....
Posted by: 1955CJ-5
« on: June 11, 2014, 10:06:19 PM »

I looked again. Part of that article shows a converted CJ-5 step, and the one or two pictures of the original steps don't clearly show the rear support...

Maybe someone will have a picture.......but a spacer is probably needed...
Posted by: 1955CJ-5
« on: June 11, 2014, 10:01:58 PM »

I looked at that once before, but like you, I didn't look hard enough, and didn't see it mentioned.....but I'll go try it again..

Thanks Bill!
Posted by: F Bill
« on: June 11, 2014, 09:13:29 PM »

If you click on the home page tech tips button, you will eventually find the original step installation instructions..

http://www.cj3apage.com/index/Tech_Tips/Original_side_step_instructions/Origin6.jpg


It mentions a spacer, I didn't see the dimensions listed but I didn't look too hard..
Posted by: 1955CJ-5
« on: June 11, 2014, 07:52:23 PM »

I got lucky and found a really nice pair of side steps for the '51..

Does anyone have a picture of or knowledge of the way the rear tapered vertical mount attached to the body? There is one bolt that goes through the floor and through the lip of the hat channel, but I think there is also a bolt that goes through the body side. But there is a lip under the body side so the mount will not fit up against it...was there a spacer in there or was the lip cut away?