The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:

Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: macrisel
« on: March 31, 2014, 10:12:39 AM »

On a side note, I really appreciate all the help everyone gave me on this.  It took a while to figure it out and I was scratching my head several times.

Everytime I open the hood on the jeep for something, it seems is isn't long before I'm also opening the laptop and pulling up this forum.

Thanks again to a great bunch of guys.
Posted by: macrisel
« on: March 31, 2014, 09:56:10 AM »

Well.........I'll keep it 6 volt for now.  I took great pains in trying to keep this jeep original so I'll fly that course for now.  Maybe sometime in the future I'll switch it over to 12 volt if I change how I use the jeep.  I'm not planning on adding any modern accessories (radio, winch, lights) right now so I should be okay.  In addition, I've already bought a 6 volt battery tender and I would hate for that to go to waste.

However..........for my next Willys project sitting in the shed I can make no promises about keeping it original..... ;)
Posted by: Carls_jeep
« on: March 29, 2014, 11:38:50 AM »

My Jeep is 12v also and I have no starter problems. If your planning to use a winch and other high amp draw equipment get the highest amp alt. you can. I have a 60A alt and it helps with the winch use.
Posted by: Gunslinger
« on: March 29, 2014, 10:24:55 AM »

Mine is converted to 12 volt, I like it as I can use some of the modern accessories easier, ie winches and lights.  I used a coil with an internal resistor, this drops the voltage to 8 volts.  Make sure you change your head lights as well, and yes it does make the starter really whirr!  I've had this conversion for about 3 years now and have not had a problem with the starter burning out. 
Posted by: 1955CJ-5
« on: March 28, 2014, 04:40:07 PM »

12 volt...Really?

After all that trouble you went through to repair your generator mount?

It seems to me that the resistor keeps the ignition at 6v anyway, but the starter will crank faster!
Posted by: macrisel
« on: March 28, 2014, 04:29:26 PM »

Quote
Sweet!!! 12V conversion be damned!!

Whoa, whoa, whoa....lets not get ahead of ourselves Ryan.. :-?

By the way, if anyone is interested I contacted Willys Distributers (the link Carl and Randy posted) about rebuilding my distributer and they were very polite and seemed very experienced on these ditributers.  However.....due to demands from his day job he stated his current turnaround time was 3-4 months on rebuilds.
Posted by: Ryan_M
« on: March 28, 2014, 02:52:47 PM »

Sweet!!! 12V conversion be damned!!
Posted by: 1955CJ-5
« on: March 28, 2014, 12:25:07 PM »

Hooray!
Posted by: macrisel
« on: March 28, 2014, 12:14:35 PM »

I finally managed to get back out into the shop last night and work on my distributer.  I took great pains to make gaskets to insulate the breaker plate assembly from the distributer housing and used heat shrink tubing to insulate the machine screw where the coil wire hooks up.  I even went so far as to make a gasket to fit on the outside of the distributer over the same screw to (hopefully) keep out some moisture.

After all of that, I took a Dremel with a small wire wheel cleaned up all the contact points to make sure I would get a solid contact on everything.  Finally, I took my meter and checked for continuity and verified I didn't have anything grounding out where it shouldn't be.  To the best of my knowledge, everything appeared to be working as it should....

I then decided to go the extra mile and put the distributer back in the jeep and give it a go.  I made extra sure to get the disty seated into the oil pump and even used a rubber mallet to make sure it was completly bottomed out.  I brought the motor up to TDC, lined up the rotor button and the cap, strapped everything down, pumped the gas twice, kicked the starter.............and the motor hit once, fluttered and died.  One more pump on the gas, kick the starter and the motor hit and took off and started running!  I almost jumped out the seat I was so happy!  I pumped the gas and everything revved up all the way as it should.  What a relief..

I didn't get to take it for a drive due to the monsoon that was going on last night.  I'm hoping this evening or this weekend to take it out and put it through its paces.  It still seems it is running rich, but no more than it was before all this was started two weeks ago.

Fingers crossed!!
Posted by: Carls_jeep
« on: March 25, 2014, 09:57:30 AM »

Mark, try these people for parts for your distributor. http://willysdistributors.com/ I got it from the G503 site.
Posted by: scoutpilot
« on: March 25, 2014, 05:23:44 AM »

[size=12]I venture to say half the distributors out there don't have dust covers. They are another layer of protection from dirt, water, fuel and oil.[/size][/b]
Posted by: macrisel
« on: March 24, 2014, 03:33:18 PM »

Oh, one more thing.  On looking at the link that Randy posted I noticed my distributer does not have a dust cover inside.  Will this really affect anything?
Posted by: macrisel
« on: March 24, 2014, 03:30:54 PM »

Carl, I may have misspoke but there is not a gasket between the breaker plate and distributer plate..but there is one between the breaker plate and the case of the distributer that was pretty rotten.

Randy, I do have a continuity tester I'll hook up tonight.  I ran out of shop time yesterday.  The heat shrink tubing is a good idea and I'll probably use it along with the cork/rubber gaskets.  Instead of messing with the carbon button, I just replaced the entire cap.

Bob, I will definatly make sure I rotate the motor while I'm checking for current.  Right now, the disty is pulled back out and disassembled on my workbench while I wonder what went wrong.  It is my luck nothing was broke until I fixed it..........

Does anyone have a photo of the original insulators I could copy from?
Posted by: Bob W
« on: March 24, 2014, 01:01:54 PM »

Quote
When I touch a test light to the coil wire on the distributer (with the ignition on) I get nothing.  Moving back to the coil, I get current on the key side of the coil but not on the distributer side....until I unhook the distributer wire.  This leads me to believe the distributer has a short in it somewhere........right?  Where else can I look for a short?
I agree with the posts above, sounds like you have an unwanted ground. Just keep in mind that when the points are closed the test light will not light up on the distributor side of the coil, only when the points are open. Try testing while cranking the engine, the light should flash as the points open and close.
Posted by: 1955CJ-5
« on: March 24, 2014, 10:40:07 AM »

It sounds like you have a short all right. Do you have a meter with a continuity function? You can hook it up and wiggle things around and see if there is a short....

There have been a couple of fellows over at the CJ-2a page that have had the electronic ignitions quit working. The thing about points, is they will typically keep working even though the engine may run poorly...when the electronic ignition quits, your done..

Did you replace the little carbon button or use a new cap?

You could probably use a piece of heat-shrink tubing to insulate that stud that goes through the distributor side, along with gasket/cork material on each end....It sounds like maybe the original insulator had already been replaced....