The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:

Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: 1955CJ-5
« on: November 14, 2013, 11:28:48 AM »

Quote
So all this talk about driving out end bushings and such has me confused.
I bought my springs from Walk's and simply bolted them in place.
Is this another case of KW parts not being quite what they ought to be?
Carl told me his springs were US made.

I've bought several parts from KW and even more from Walk's.
My experience with KW has been that you need to know more than they do which, in my case, isn't that big a problem.
With Carl Walk, on the other hand, he knows WAY more than I'll ever know and he's been dead-on correct every time I've had a question.

KW are nice people and their prices and service are good, but they simply are NOT as knowledgeable as Carl. Put him together with Herm the Overdrive Guy and you may well have all that is possible to be known about old Willys.

I agree 100%...

I put a set of four Walck's spring packs on my CJ-5. They went on fine and work great.

The set of four spring packs on the 3A were from Kaiser-Willys in their "Master rebuilt" suspension kit. Crown automotive springs...really difficult to install the U bolt shackles and pretty stiff.

KW may source their springs from different suppliers depending on where you live. With free shipping offered it's in their interest to find the nearest supplier. Mine came from Reno/Sparks Nevada, about 400 miles away...
Posted by: Ryan_M
« on: November 14, 2013, 10:57:12 AM »

My OMIX springs as purchased from KW were not that difficult to replace. They were one of the first things I did and being ultra-green at this stuff at the time any problem would have been a huge challenge. As far as I remember they just bolted right up.
Posted by: johnrb3b
« on: November 14, 2013, 10:43:02 AM »

So all this talk about driving out end bushings and such has me confused.
I bought my springs from Walk's and simply bolted them in place.
Is this another case of KW parts not being quite what they ought to be?
Carl told me his springs were US made.

I've bought several parts from KW and even more from Walk's.
My experience with KW has been that you need to know more than they do which, in my case, isn't that big a problem.
With Carl Walk, on the other hand, he knows WAY more than I'll ever know and he's been dead-on correct every time I've had a question.

KW are nice people and their prices and service are good, but they simply are NOT as knowledgeable as Carl. Put him together with Herm the Overdrive Guy and you may well have all that is possible to be known about old Willys.
Posted by: Tumbleweed
« on: November 12, 2013, 05:12:04 PM »

I got mine from KW as well - Omix Ada - I had a $25.00 credit at KW and then they had a 10% discount with free freight. Total 4 springs (9 & 10 leaf) around $425

Check out tech talk - they are a bear to install the U shackles on the rear for some reason. Non of mine had the bushings installed. With no weight on the front end the 10 leaf springs feel solid.
Posted by: Ryan_M
« on: November 12, 2013, 04:34:04 PM »

I was just flipping back through some rebuild pics and I stumbled across my springs fresh out of the box - turns out they are OMIX-ADA afterall! I bought them from Kaiserwillys but they can be had MUCH cheaper from other sources. I'm running 9 leaf on the rear and 8 on the front. If they have sagged it's been very slight. I have nearly 2 years (1 year actually running) with these springs and nearly 3500 miles. No issues yet.
Posted by: Gunslinger
« on: October 18, 2013, 09:54:45 PM »

I bought the Omix Ada springs for the front of mine, drove out the bushing and have been pretty happy with them.  For the back I bought a recurve kit from 4 wheel drive parts.  It's a heavy short spring that fits on the bottom of the spring pack.  I had to pull two springs to get them on.  But it pushes the spring pack back into the right curvature and seems to eliminate the jeep list.  I've been happy with them, nice enough ride and fair enough load capacity.
Posted by: 1955CJ-5
« on: October 16, 2013, 10:56:02 AM »

Yes you can drive those bushings out...find a socket with an OD that fits well and support the spring so the bushing has someplace to go...One came out pretty easily for me and the other was tough. The socket looks kinda beat up but I didn't have an alternative tool.
Posted by: 3aJeeper
« on: October 16, 2013, 10:13:59 AM »

I'm putting new leaf springs on the front. They are OMIX-ADA. The one challenge I found (too late to return) was that the front curl for the shackle brackets had bushings installed. These were too small for the shackles to fit. The rear curl also has a bushing and the rear pin fits like a glove.

I guess I'm going to have to drill out the front bushings so the shackles will fit. Anyone else run into this?
Posted by: johnrb3b
« on: October 16, 2013, 09:26:04 AM »

Quote
That's interesting I guess I would want the springs just stiff enough that the tire won't rub the inside of the wheel well during axle articulation.� Yet soft enough to enjoy a cruise.� Not sure how to arrive at this ...
That's where Alcan comes in. They will ask you what payload capacity you'll want for your rear springs. They'll even ask you if you'll be mounting a spare tire on the rear - that's an extra 40 lbs or so.
So you tell them you have a spare tire, a back seat and two small adults as rear seat passengers (or whatever you envision) as your maximum anticipated load and they'll take it from there.

Yes there's still some guesswork involved, but you'll come much closer than just randomly buying some "OEM reproduction" springs from a vendor.

And remember, when a CJ was new, it did ride like a truck. Willys assumed you'd put a half ton of stuff in the back. That's what it was designed for.

But they still rode like a truck. The harsh ride of the Jeep in WWII caused a condition known as "Jeep Seat".
http://en.wikipedia.org/wiki/Pilonidal_cyst
Relevant quote from that article:
"The condition was widespread in the United States Army during World War II. More than eighty thousand soldiers having the condition required hospitalization; [12] the average length of these wartime hospital stays was 55 days.[13] The condition was termed "jeep seat" or "Jeep riders' disease", because a large portion of people who were being hospitalized for it rode in Jeeps, and prolonged rides in the bumpy vehicles were believed to have caused the condition due to irritation and pressure on the coccyx."

More than you ever wanted to know.
 ;D ;D ;D
Posted by: johnrb3b
« on: October 16, 2013, 09:21:52 AM »

Interesting.
The stock springs on the 3B were 10 front and 9 rear.
So the heavy duty fronts from the 3A became the standard for the 3B. Extra weight of the F-head engine? Who knows?
Posted by: Quebec Jeep
« on: October 16, 2013, 08:26:01 AM »

Ok, I checked.

In my Part list book models CJ-2A and CJ-3A third edition 1949
Page 98

Group 27-01 Front spring
front spring assembly part # A-612 is 8 leaves

Group 27-01A Front spring Heavy duty
front spring assembly part # A-8463 is 10 leaves

Group 27-02 Rear spring
rear spring assembly part # A-614 is 9 leaves

Group 27-02A Rear spring Heavy duty
rear spring assembly part # A-15728 is 11 leaves

Heavy duty option is after serial # 169923
Posted by: 1955CJ-5
« on: October 15, 2013, 05:51:54 PM »

Quote
Hi Randy,

I think the 10 front, 9 rear is the stock configuration for a 3A.� I'm guessing that the CJ5 is heavier than a 3A, but not much.� �

What do you have on your current project?

Tim


I went with the same leaf count, 10 front and 9 rear, but they are Kaiser-Willys, (actually Crown Automotive) springs and they feel a bit stiffer than the Walck's springs. But without the body mounted it tough to tell....

The original packs I took off the 3a were 10 front and 9 rear....

The parts book shows 10 front and 9 rear as standard, and 10 front 11 rear as heavy duty. It also lists the lengths of the separate leaves, which will affect stiffness.....
Posted by: Quebec Jeep
« on: October 15, 2013, 03:31:00 PM »

I think it's:

For a CJ3A
Standard (stock) leaf is 8 at the front and 9 at the rear.

The heavy duty option was 10 at the front and 11 at the rear.

will check tonight in the part manual
Posted by: athawk11
« on: October 15, 2013, 02:49:41 PM »

Hi Randy,

I think the 10 front, 9 rear is the stock configuration for a 3A.  I'm guessing that the CJ5 is heavier than a 3A, but not much.   

What do you have on your current project?

Tim
Posted by: 1955CJ-5
« on: October 15, 2013, 11:46:59 AM »

For the CJ-5, I put ten leaf packs on the front and nine leaf packs on the rear....all from Walck's....I like the ride..

Now it had 13 leaf fronts and 13 rear originally, so it used to be really stiff...