The CJ3A Page CJ3B.info

Post reply

Warning: this topic has not been posted in for at least 120 days.
Unless you're sure you want to reply, please consider starting a new topic.

Note: this post will not display until it's been approved by a moderator.

Name:
Email:
Subject:
Message icon:

Verification:
Type the letters shown in the picture
Listen to the letters / Request another image

Type the letters shown in the picture:
Write the word between words Jeep from this JeepWILLYSJeep?:
How many slot has a GPW grill?  7 - 9 - 11:

shortcuts: hit alt+s to submit/post or alt+p to preview


Topic Summary

Posted by: Macgraham
« on: February 01, 2012, 05:34:27 PM »

It was afuel valve to switch tanks. Both tanks were full of rust so I got a new tank and eliminated the valve.
Posted by: Matto
« on: February 01, 2012, 04:28:08 PM »

Mac, Is that a fuel petcock or spare tank manifold on the floor between the gas pedal and tank in pic#2?
Posted by: bretto
« on: February 01, 2012, 12:36:14 PM »

Tip:
To have pics show up here, surround them with url]enter link here[/url �(put the brackets also on the ends. �i cant get it show here right if i try to give an example)
Photobucket makes it even easier. �There is a box called 'links', click on 'IMG Code'. �It will copy the wording for you then you can paste it in your post.
Posted by: Macgraham
« on: February 01, 2012, 08:08:18 AM »

<a href="http://s1067.photobucket.com/albums/u424/macgraham/JEEP%20REBUILD/?action=view&amp;current=PA270017.jpg" target="_blank"><img src="http://i1067.photobucket.com/albums/u424/macgraham/JEEP%20REBUILD/PA270017.jpg" border="0"

alt="Photobucket"></a>


Here is a pic of the gastank door on the pass side. I have removed it and and welded it up.
Posted by: Macgraham
« on: February 01, 2012, 07:36:34 AM »

The toolbox is not welded down in that pic. there was another gas tank under the pass. seat and I took it out and got a toolbox. This made it possible to have the proper passenger seat as the hinges bolt to the toolbox.
Posted by: bretto
« on: February 01, 2012, 06:55:58 AM »

Is it just me or is your toolbox floating on the center side and not welded down?
Posted by: rocketeer
« on: January 31, 2012, 09:33:50 PM »

The right side leg should sit outside of the gas tank. That hole under the leg doesn't belong there.







Larry
Posted by: Macgraham
« on: January 31, 2012, 08:38:31 PM »

I've been puzzled for a long time. I sent back the original frame I bought and they sent me another one. Same problem. The inner fenders are 32 inches which I think indicates 3A. I know something is not right here which is in keeping with the rest of the Jeep. It looks like a new floor pan was welded in at one time. What next!!
Posted by: athawk11
« on: January 31, 2012, 07:49:57 PM »

Hey Mac.

Your photo puzzled me. �I went out to look at mine, then got more puzzled. �I scrolled back and looked at your #10 photo on Photobucket and it seemed as if the seat frame or the tank is mis-positioned or too large. �The tank looks just like mine. �

Is the seat frame a new repro? �I must warn you, I have 2A seats in a 3A Willys, but they bolted right up in the same holes. I haven't seen a 3A seat up close, and they are different than mine, but your seat frame seems too wide and maybe too long. �At the front, top, just before the curve down, I measured 20 1/2" from outside of tube to outside of tube.  Is the rear wheel house a 2A?  They are larger and that may push your seat too far forward.�

Here are a couple photos of mine. �



I know I'm not helping. �Perhaps a 3A seat owner will chime in.


Tim