The CJ3A Page CJ3B.info
« previous next »
Pages: [1]   Go Down

Author Topic: Exhaust Manifold Washer??  (Read 2982 times)

0 Members and 1 Guest are viewing this topic.

Offline 1955CJ-5

  • Flatfender Master
  • *****
  • Posts: 2360
  • Karma: +0/-1
  • It wasn't always green....
    • View Profile
Exhaust Manifold Washer??
« on: April 18, 2014, 11:53:27 AM »
I learned over at the 2a forum that there is supposed to be a special thick washer on each of the two innermost manifold studs. This washer is concave on the one side to allow even tension on the two intake and exhaust manifold ears.....

Anyone have a picture of one, or dimensions? I'm told that they are about 1/4" thick, slightly rounded on top, concave on the bottom....

Thanks,

Randy
Logged
1955 CJ-5, A friend for 58 years....1951 CJ-3A, a new addition. 1929 Model A Ford Closed Cab Pickup...

Offline 1955CJ-5

  • Flatfender Master
  • *****
  • Posts: 2360
  • Karma: +0/-1
  • It wasn't always green....
    • View Profile
Re: Exhaust Manifold Washer??
« Reply #1 on: April 18, 2014, 12:11:45 PM »
Well, it seems all you need to do is ask a question and the answer suddenly comes to you...

I googled the part number from the parts list..344732...and it turns out that Ron Fitzpatrick has them in stock...

g503.com



Logged
1955 CJ-5, A friend for 58 years....1951 CJ-3A, a new addition. 1929 Model A Ford Closed Cab Pickup...

Offline 1955CJ-5

  • Flatfender Master
  • *****
  • Posts: 2360
  • Karma: +0/-1
  • It wasn't always green....
    • View Profile
Re: Exhaust Manifold Washer??
« Reply #2 on: April 21, 2014, 08:16:18 PM »
Washers arrived and are installed.....I'm sure there is more even pressure on the manifold ears...

Washers are .873 dia by .130 thick with a .408 hole, give or take a little...cheap calipers you know....

« Last Edit: April 21, 2014, 08:17:42 PM by 1955CJ-5 »
Logged
1955 CJ-5, A friend for 58 years....1951 CJ-3A, a new addition. 1929 Model A Ford Closed Cab Pickup...

Offline Ryan_M

  • Flatfender Master
  • *****
  • Posts: 1704
  • Karma: +0/-0
    • View Profile
Re: Exhaust Manifold Washer??
« Reply #3 on: August 11, 2014, 04:11:48 PM »
My 3A is in need of a valve adjustment and while I have the fender off I figured I would replace the intake/exhaust manifold gasket as I've had an annoying exhaust leak there for a very long time.

Remembering this thread, I just this morning ordered the two washers from Ron Fitzpatrick.

I also took a fresh look at the M38 service manual and noticed it calls for "13/32 ID flat washers" on the two center studs. No mention of any special concave washers. I'm still going ahead with the concave washers but I figured it was worth noting here that it appears they were discontinued, at least for the M38. I wonder if it was determined the flat washers were just as effective or if there was another reason for simplifying the parts requirement a bit?
Logged
Current:
'49 CJ3A
'51 CJ3A
'42 Willys MB-T
'47 Bantam T3-C
Previous:
'46 2A
'51 3A
'52 3A
'52 M38
'54 3B
East Coast Wi

Offline 1955CJ-5

  • Flatfender Master
  • *****
  • Posts: 2360
  • Karma: +0/-1
  • It wasn't always green....
    • View Profile
Re: Exhaust Manifold Washer??
« Reply #4 on: August 11, 2014, 04:30:55 PM »
In reality those washers were pretty flat on the backside, but they are thicker than regular washers and shaped as you see in the picture....I'm sure they help distribute the load even if they are not really concave on the back....
Logged
1955 CJ-5, A friend for 58 years....1951 CJ-3A, a new addition. 1929 Model A Ford Closed Cab Pickup...

Offline Ryan_M

  • Flatfender Master
  • *****
  • Posts: 1704
  • Karma: +0/-0
    • View Profile
Re: Exhaust Manifold Washer??
« Reply #5 on: August 13, 2014, 05:33:01 PM »
How did you determine which direction those washers go on? It almost seems like the rounded side should go towards the manifold and the flat side against the nut
Logged
Current:
'49 CJ3A
'51 CJ3A
'42 Willys MB-T
'47 Bantam T3-C
Previous:
'46 2A
'51 3A
'52 3A
'52 M38
'54 3B
East Coast Wi

Offline 1955CJ-5

  • Flatfender Master
  • *****
  • Posts: 2360
  • Karma: +0/-1
  • It wasn't always green....
    • View Profile
Re: Exhaust Manifold Washer??
« Reply #6 on: August 13, 2014, 05:44:33 PM »
I think the idea is to spread the load over more area of the manifold ear casting...so the best (in my humble opinion) is to have the flat towards the casting and the convex side towards the nut.... ;)
« Last Edit: August 13, 2014, 05:45:20 PM by 1955CJ-5 »
Logged
1955 CJ-5, A friend for 58 years....1951 CJ-3A, a new addition. 1929 Model A Ford Closed Cab Pickup...

Offline Ryan_M

  • Flatfender Master
  • *****
  • Posts: 1704
  • Karma: +0/-0
    • View Profile
Re: Exhaust Manifold Washer??
« Reply #7 on: August 13, 2014, 05:48:50 PM »
Can I split my odds and install each one in a different direction?  ;D
Logged
Current:
'49 CJ3A
'51 CJ3A
'42 Willys MB-T
'47 Bantam T3-C
Previous:
'46 2A
'51 3A
'52 3A
'52 M38
'54 3B
East Coast Wi
Pages: [1]   Go Up
« previous next »