The CJ3A Page CJ3B.info

Author Topic: Latest engine project  (Read 6430 times)

0 Members and 1 Guest are viewing this topic.

Offline garage gnome

  • Flatfender Master
  • *****
  • Posts: 1947
  • Karma: +0/-0
  • Rustologist
    • View Profile
Latest engine project
« on: September 26, 2013, 08:00:17 PM »
My latest engine project is a 1925 3HP Fairbanks Morse Z, whoop dee doo, nothing special. Probably one of the most common engines around. [size=18]BUT,[/size] this one has a very rare magneto setup on it. These came with a Fairbanks brand rotary mag. This one has a conversion kit offered by Wico that uses a Wico EK mag. Anyways, it was a basket case and I got it running again. It needed some headwork, rings and needle valves for the mixer.

http://www.youtube.com/watch?v=-ZWIC0Z6Ukg
Nate in Western MA 1953 3A #3268, The Jalopy, '47 2A Wheelin' rig, '49 3A, #37071, unmolested, bone stock named Ted

Offline F Bill

  • Flatfender Master
  • *****
  • Posts: 1402
  • Karma: +1/-0
    • View Profile
Re: Latest engine project
« Reply #1 on: September 26, 2013, 08:30:54 PM »
Speaking of common engines, I am spending time in Newton, IA, home of Maytag.. Local antique store has a kick start maytag small motor, wants $145 for it.. Deal or no?
Owner of the world famous?? Pintojeep 3A and one yet to be named stock project 3A.
Based in central TX and upstate NY.

Offline garage gnome

  • Flatfender Master
  • *****
  • Posts: 1947
  • Karma: +0/-0
  • Rustologist
    • View Profile
Re: Latest engine project
« Reply #2 on: September 26, 2013, 09:53:50 PM »
Mehh, maytags, I don't pay much attention to them things. Loud and smokey things. Is is a horizontal 1cyl, vertical 1cyl, or horizontal 2 cylinder? That is pretty cheap.
Nate in Western MA 1953 3A #3268, The Jalopy, '47 2A Wheelin' rig, '49 3A, #37071, unmolested, bone stock named Ted

Offline F Bill

  • Flatfender Master
  • *****
  • Posts: 1402
  • Karma: +1/-0
    • View Profile
Re: Latest engine project
« Reply #3 on: September 27, 2013, 07:56:54 AM »
Very small one cylinder, horizontal from what I can tell. I will try to stop in there sometime and get a picture for ya. Not much bigger if at all  than a Briggs and Stratton 3hp. 
Owner of the world famous?? Pintojeep 3A and one yet to be named stock project 3A.
Based in central TX and upstate NY.

Offline garage gnome

  • Flatfender Master
  • *****
  • Posts: 1947
  • Karma: +0/-0
  • Rustologist
    • View Profile
Re: Latest engine project
« Reply #4 on: September 27, 2013, 09:56:18 AM »
It is probably a model 92, the most common.

model 92


model 72


model 82


upright maytag
Nate in Western MA 1953 3A #3268, The Jalopy, '47 2A Wheelin' rig, '49 3A, #37071, unmolested, bone stock named Ted

Offline johnrb3b

  • SMF Administrator
  • Flatfender Master
  • *****
  • Posts: 906
  • Karma: +0/-0
  • No such thing as too many Jeeps - well maybe
    • View Profile
    • Jeeps and stuff
Re: Latest engine project
« Reply #5 on: September 27, 2013, 10:41:35 AM »
Hi Natei
Sounds like the engine you showed us in the shop with the pavement queen.
So it's running already? Cool.
Good to see you're still around.
1946 2A - - - 1949 me - older than most of my Jeeps
1954 3B - - - 1957 Wagon - - - 2010 4-door JK
past Jeeps ---> '54 3B - no tub --- '59 3B - no engine
past addiction - VW ---> '69 bus --- '70 camper

Offline F Bill

  • Flatfender Master
  • *****
  • Posts: 1402
  • Karma: +1/-0
    • View Profile
Re: Latest engine project
« Reply #6 on: September 27, 2013, 08:02:48 PM »
Second one down is it.. And just like the one in your picture it has a blank flange with no carb......but it does have a totally different muffler thing off the other side. No spark plugs... They said they would take ten percent off the $147 which gets it down to 132.30 plus tax.
Owner of the world famous?? Pintojeep 3A and one yet to be named stock project 3A.
Based in central TX and upstate NY.

Offline F Bill

  • Flatfender Master
  • *****
  • Posts: 1402
  • Karma: +1/-0
    • View Profile
Re: Latest engine project
« Reply #7 on: September 27, 2013, 08:04:22 PM »
BTW I know I said it was a one cylinder but my memory unit was glitching again. IT is two horizontally opposed. I didn't find any model ID on it but it did have some magneto company and made for Maytag in Newton IA on the flywheel, which is aluminum.
Owner of the world famous?? Pintojeep 3A and one yet to be named stock project 3A.
Based in central TX and upstate NY.