The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - BobM

Pages: [1] 2
1
Perfect! Thanks a ton squidtone!

I think Russ might be on to something. I wonder how many hood and fender combinations would actually "line Up"? I am going to match your location. That fender location on the spring latch, seems to put the first hole on the hood catch just behind the grill.

2
Does anyone have the location of the hood catches on the front fender? I am finishing up my body kit and, I cannot find any "exact" location to drill the holes in the hood and fender for the attaching screws.

3
Oh wow that's it! I also have the dealer installed air bags. This was a Jeep used for farming. It only had 43,000 miles on it. It was beat as bad as it gets however! I will take the plate out. It is the only piece I have of the shroud you have pointed out. I guess it and the air bags will go up as garage "wall art". 

Thanks a lot!

4
I am getting things back together. After I reinstalled the e-Brake asy, I remembered this piece that was bolted to the skid plate under the drum. I can't find any reference to it. It appears to protect the drum? It bolts to the skid plate with 4 carriage bolts. The plate is cut for the bolts. It seems like there is something missing in the back. There are two holes that appear to have a purpose. Any ideas?

5
Thanks a ton! I was sweating it. I thought I may have split the bore inside the case. The shaft was tight but, nothing serious. Maybe a tad tighter than the counter shaft. Once it cleared the case front it was fairly easy to tap it the rest of the way into the case and remove it.

There are a lot of guys trying to push it through from inside the case, with all kinds of ways. I wonder if Rick could update the instructions. They are very good. I had not seen them. I was using the manual. I have the box torn down and parts just arrived. Now that I have read Rick's guide, I am finding it an excellent guide.

6
I do know that the manual has been wrong before. Specifically the process for rebuilding the water pump. I believe more than one person has ruined a pulley taking a pump apart per the manual.

I hope someone can shed a little light. What can happen when you drive a T90 rev idler into the case?

7
Quote
I have always followed the advice laid out in Rick Stivers T90 rebuild guide.� He too was pretty adamant that the idler shaft should be driven out the back of the case.

http://www.willystech.com/wt/T90RebuildGuide/T90rebuild.htm


I was reading Ricks guide where I found the info. He is clear about driving it to the outside of the case. I can only say, I followed the manual, drove to the INSIDE and it worked quite well as far as I can tell. The shaft came out fairly easy to the INSIDE of the case as the manual indicates it should be done. Maybe it can be done either way? It would be great if someone could clarify this.

8
I am at a loss! Maybe the writers got mixed up with the model. Right now I am at a loss. Either the manual is wrong or, the web page instruction for the T90 on the CJ3A page is misquoted.

9
I am right in the middle of the T90 trans on my CJ3A. I have it torn down inspected and parts ordered. I used the Service Manual for Universal Jeep Vehicles as a guide. It was fairly straight forward nothing unusual. A LOT of water damage.

The service manual page 168, indicates you "remove the reverse idler shaft by driving it into the case with a brass drift" A procedure I followed right down to the brass drift. I had no trouble. I drove the shaft out by completely driving it into the case and, removing it. All seems good.

As I was looking for parts on the WWW, I noticed a tear down article on the CJ web page. The writers stated to NEVER drive the reverse idler shaft into the case as it will damage the case and will not come out that way? I just did that and it seemed to work fine. Is the service manual incorrect? I wonder if I damaged the case? I then read in more than one forum about persons having a very difficult time getting the reverse shaft out. All kinds of ideas on how to perform this difficult task. All focused on getting the shaft out via the outside of the case. I had zero trouble driving it into the case with a brass drift per the manual. What gives here? Can anyone shed a little light?

10
Good call you guy's! It is shimmed correctly. I have a nice light load on the shaft.
The problem was exactly as specialty thought. The Sector shaft backlash screw was in to far. Russ is also right on 2 and 5/8 turns lock to lock.
When I set it up on the bench I was paying attention to the drag through he middle on the adjustment. I forgot to even check full sweep. Set up that way, it hits the the end pads on the sector shaft and stops it. I had to adjust it for a slight drag across the end stop and the middle is what it is. The middle pad is worn down further than the ends. As designed the middle should be the tight spot. Oh well it Doesn't seem to loose in the high point. I hope it will be oK. I guess a new sector shaft would fix all.
Thanks guy's!


11
OK at the risk of sounding like a Jeep rookie, How many turns should you get on the Ross steering box in the 1950 CJ3A? I just finished up the steering system. The box rebuild went well. I had to replace the tube/worm gear assembly because the threads at the steering wheel were destroyed. The sector shaft and bushings were perfect and not replaced. New snap ring and bearings (the type that are captured in plastic for easy install). It went back together well and turns smoothly. I am at a loss however for how far it turns. I am only getting one and a little over a half turns of the steering wheel lock to lock. It doesn't seem like it turns the wheels much. All the geometry is to the book. The wheel ends do not come anywhere near the stops on the axle tubes. Is this all the turning there is? I hope all is good! Am I learning about the turning radius of a 1950 Jeep?

12
Just received these from Patti Bradley at Warn Hubs. The part number is 29062. Thought I'd share!

13
Did you get this figured out? Basically those clearances aren't critical. The axle shafts in reality bump on the snap ring and the bushing to control end play. Many times the axle snap ring is left off on the Dana Spicer style u-joint shafts. In this case the axle shaft simply bumps inside the diff at the cross shaft. This is the way many axles operate. As long as the axle shafts go in and all assembles, you are good. There should be a small amount of "play" in and out on the axle shaft. All it needs is "some". Hope that helps.
Bob

14
Your CJ-3A Project / Re: Some rare stuff?
« on: March 14, 2019, 07:55:12 PM »
I am going to use the adapter in this build. I am trying to put it back together with as many of the parts as I can. It will be close to a restore but a few discrepancies will occur. I will have a built in conversation starter for sure!

I see what appears to be a casting mark on yours. And a fairly clear casting number. If that is a "Circle B" They were made by Buckeye Steel Casting Company out of Columbus Ohio. This is wild! An excerpt from Wikipedia..... "best known today for its longtime president, Samuel P. Bush, who was the grandfather of President George H.W. Bush and great-grandfather of President George W. Bush." Ha ha! These Jeeps are just full of history!

https://www.google.com/search?client=firefox-b-1-d&q=casting+foundry+marks

https://en.wikipedia.org/wiki/Columbus_Castings

I'll keep going with the updates. I should list some of the things I am running into. The lift was a gift to myself to preserve my old body! I swore I was done crawling under cars in the stones!

15
Your CJ-3A Project / Re: Some rare stuff?
« on: March 14, 2019, 10:05:13 AM »
Your eye is awesome! I stuck another pic for your scrutiny. My cell phone snaps are not real good but, you can see the mount and the fuel pump. Not the correct fuel pump however. Another indication of the economy during rebuild/repair. The only thing that may help understand how the engine got in there would be the original owner. It is possible the adapter was installed by a dealer or shop during a rebuild. There is no recollection that this occurred however. The motor was rebuilt at least twice. It was bored, and then some time later it was honed and knurled, probably when it started smoking again! Since so much time was spent trying to keep the original block (boring it then tearing it down again and knurling the pistons) it seems like they were trying to avoid a new block.

The old timers definitely remember using up inventory at the plant. Times were tight all through the 1940's 1950' and even the 60's. They used everything of value. One thing to note on the actual adapter. It is an investment casting. It would have required a mold etc. to produce. This process is of course used on moderate to high volume parts over using simple fabrication. In other words Willy's made at least a few casing runs. There has to be a bunch of these (adapters), relatively speaking. It must have been used quite a bit in the service market as you spoke of. The block and motor plate could have been swapped during one of the rebuilds. It sure seems that quite a few of those adapters must have been made available.

The bolts on the head were some of the casualties of many mechanical errors/substitutions made on the farm. In fact I used the "bolt from stud" error to point out something during the motor machining. The center BOLT that was put in on the drivers side had to much shoulder. When the shoulder hit the threads in the block, the force of tightening it down produced a small crack that showed up during Magnaflux. Fortunately it was easily fixed with an insert. I have seen a lot of this in my old work. Usually someone will force a bolt down into a blind hole that used to hold a stud. The crap in the hole often caused the sides of the casting to crack under the hydraulic pressure.

I do have the entire engine serial hand stamp from the boss behind the water pump. It is a 4Txxxxx. It is gone now as I had the block decked .010".

I truly appreciate your input on this! I want to get it right and having all the info is part of that. Having restored a few vehicles, this is my first Jeep. I did a 59' Chevy truck back in the 80's. I wish I would have kept it. This one is forever!

Pages: [1] 2