The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - allen

Pages: [1]
1
I just did the exact same thing about a month ago. Listen to the advice about the jack stands. Get it as high as possible while still being safe. Also spray your transfer case lever retaining pin with some PB Blaster or your choice of whatever because it will make it easier to get it out when it is time to deal with it. Search the forum for this topic because this can really slow you down if you can't get it out. While you are at it, start lining up a alignment tool for your clutch install. Search for this also as there is lots of good info on this site. One last thing, GET A TRANSMISSION JACK! It will make the job way easier, plus you have less of a chance of breaking something or you.

2
I posted about a month ago asking questions about removing the transmission because of a leak it had. Well I got the transmission out without too many problems and by the grace of God the pin holding the transfer case levers came right out which helped when getting it out from under the jeep. Well when I was cleaning the transmission I noticed the shaft coming out of the tranny had lots of play from side to side. I'm sure there is a reason for this so can someone help me figure this out. If I need to change the bearing in this location is that hard to do? I have the mechanics manual and dont see anythin about changing this bearing. Thanks in advance for the help. My jeep is a 53 CJ3A. I posted on 2A site also just to see what they had to say.

3
I changed the pressure switch out and it is leaking around the threads where it screws into the brass fitting. I removed it and put some thread sealant on it but it's still leaking. Is there a specific sealant I should use because of the brake fluid? I changed it once before and never had this problem. The first time the switch came from NAPA and the second one that leaks came from walcks ( love that place).

4

History
 
Have had jeep for 4+ years. Even though it was in good shape I have have done tons of work replacing worn out items and have driven it a good bit. The problem I'm having is the transmission is leaking alot (it is gear oil and not engine oil) until it gets below the level of the main seal in the transmission and then stops. Is it ok to drive it like this? I know there is still some gear oil in the transmission but don't want to cause any permanent damage. I promised my wife I wuld take her to and LSU game in it this year and just want to be able to do this before I get into a major job like that. I know some of you can do it in a weekend, but for me to pull that off, well lets just say it will take a little longer with work, kids and so on. I have aways planned to do a frame off, so I may just bite the bullet and go for it, but I've got to get my wife to one of those games in the jeep.

5
Well, I finally found a parts jeep close to my house and went to inspect it this morning. From the pics in the ad it looked decent except for the engine sitting in the bed of the jeep. The jeep was advertised as a 53 CJ3A (this is modle and year of mine), but after looking at it I saw it was an earlier 3A. Drive shafts are smaller in diameter and dataplate says CJ3A but not with the GB number. It was too dirty to see the rest of the plate. Upon further looking, the jeep has a complete original top bow set, a koenig pto winch on the front and the ever elusive rear back seat frame in excellent shape. To top it all off the body is in great shape, never wrecked with some rust in usual places but no where near what my body has now. I am so excited. There are tons of other small parts I can use also, plus a great windhield frame to boot. One thing I found unusual is that there is no pto handle between the seats instead there is a shaft coming out of the passenger floor next to the transmission hump with two handes on it to operate the winch. Unfortunately I dont see a shaft going to the winch but I see the linkage from the shaft on the passenger floor board going to the winch. I am so excited to find this jeep and I feel for what I paid (650.00) I got a good deal. When I pick it up on Monday I'll shoot some pics and post them.

6
(53 CJ3A) � I've been working on changing the seals on each end of the rear driveshaft and at the same time clean up and replace the shoes on the parking brake. The problem I am having is when I am re-assembling everything. When I tighten the nut on the shaft coming out of the transfer case that holds the yoke something is binding when i move the jeep in reverse (only going backwards pushing it in and out of my shop). I know I put all the shims bak in place and its not the shoes inside the brake drum(as far as I can tell) so im at a loss. If I loosen the nut to a certain point the shaft turns in both directions with no problems. The nut is on far enough that �I know it wont come off, but I know it should be tighter. I have taken it down three times and put it back together three times and am at a loss. Any help would be appreciated. As frustrated as I was I did get to hunt yesterday afternoon and was lucky enough to shoot a nice doe. I am on my way to skin and quarter it in just a little while. It got down right cold in South Louisiana last night (at least by a southerners standard) so im waiting for the sun to come up to warm things bit.

Pages: [1]