The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Jesse

Pages: [1] 2 3 ... 18
1
PAST EVENTS: / Re: Calling Minnesota jeepers
« on: August 04, 2013, 02:41:56 AM »
Where are you guys located? I'm thinking about moving back to MN this fall.

-Jesse

2
I wish I could record it for you to compare with your noise, but my jeep makes a very strange noise as well. Turns out it is the tool box lid. This sounds way too easy to be your problem, but mine does rattle at various times while driving or sitting still. It sounds bad, bad enough that I though something was wrong until the lid was noticed.

-Jesse

3
"Original"-- Technical Questions, Answers, Observations / Re: L134 Block
« on: February 10, 2016, 10:33:14 PM »
I would keep it. I traded a ww2 production block in at Midwest Military and I was shocked that he wanted it given the number of cracks between the cylinders. I figured it had gone its last mile. But there is a lot that can be done to save an engine block if you really want to.

-Jesse

4
I had good luck mixing some nice bearing grease and 90 weight oil. Had to heat the two in a soup can to get it to blend together. Let it sit a couple of days and it didn't separate back into grease and oil. I made it runny enough that it flows veryyyyyyyy slloooowwwly. Almost like honey. Pumped it into the steering box with a grease syringe and never looked back. It flows unlike grease, but is too thick to run out of the seal.


-Jesse

5
I picked up the body myself with an engine hoist if you can beg, borrow, or steal one of those. Just balanced it in the middle with 2x4s. I also ultimately screwed up the paint putting it back on with that method...

-Jesse

6
I think the maximum is about 10:1, read it a few places including here


http://www.pirate4x4.com/forum/jeep-willys/1018587-l-head-dyno.html

But if you can take that much out of a stock head or not is a different story. Maybe 8:1 with cast iron? A shop should be able to check it out and see how much could go. You could also change the pistons to some degree.

-Jesse

7
I have been thinking the same thing! I have been looking into "blank slate" programs that can be set up with all of the various parameters and inputs needed for EFI. I'm thinking about doing port injection, which is a throttle body and injectors for each cylinder.


...then I'm going to turbocharge it  :D

Here is a website I have checked out.
http://www.diyautotune.com

Maybe you can use the throttle body from a pinto, about the same engine displacement.

-Jesse

8
Here is the test stand I built about 7 years ago, I think its pretty slick. You can easily move it where ever you need it. It has a radiator mount, fuel supply, and a full array of gauges. Pretty easy to put together for a couple grand, less if you buy and sell pieces as you go.






-Jesse

9
BMIC,

I was kept awake at night about what oil I was going to use a full two years before the jeep was on the road!

-Jesse

10
...or a bit of moonshine for the winter months   ;)

-Jesse

11
"Original"-- Technical Questions, Answers, Observations / Re: 3A and 3B
« on: January 18, 2015, 03:10:17 PM »
Well, my lovely assistant is about 5 foot four and she can drive the jeep without issues. These things are cramped for bigger people. You could add some different seat cushions pretty easily if you wanted.



-Jesse

12
Haha cheers aboyandhisdog, looks like we have jeep twins!


I think I took my carrier from a nissan pathfinder (?) I cut a good foot off the end where it attaches to the tailgate.

-Jesse

13
It attaches to the drivers side with the tailgate hook.



Overall it turned out fine. I would lower the tire on the carrier if I did it over. But ultimately the tire -just- squeaks by the winch, so it worked out in the end.




Hopefully this gives you some ideas. Not the most pro job but it has worked for the last 5 years. 8-)
-Jesse

14




This is the inside, I basically cut off the outside loop of the carrier


15
Yes! Finally a topic I can contribute to. I added a junkyard tire carrier to my jeep. I'll get you some pics and details in a little bit.


-I'm Back-
So this carrier is mounted on the passenger side with these brackets, the bottom one has threaded rod welded to it to connect it to the roll bar mount inside the wheel well. The top has a backing plate.






Pages: [1] 2 3 ... 18