The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - specialty

Pages: [1] 2 3 ... 16
1
Did you shim it right  at the top? Been awhile since I messed with mine but if the set screw is to tight it will hit on the high side of the shaft and lock it up. Might try backing it off a little

2
Here is a real nice Duaghtless V6 and transmission close to me in west Va. Owner claims only 45,000 miles. Probably to far for you though. I I had the spare change I would buy it.

https://martinsburg.craigslist.org/pts/d/jeep-engine/6747589050.html

3
You may have to stick with the "Go Devil" you have. You could go with the odd fire Dauntless V6 Buick also but they are becoming few and far between. Or there is the 3B overhead valve option but that requires  cutting up your hood some. I would think that any engine with more power than what you have may require better brakes and steering plus you have to adapt to the transmission and the transfer case unless you do a all out custom. I bought a tub off a guy that put a late model 4 cylinder Chevy engine in his bt with 180hp I am sure he switched out the steering and brakes. Just depends on how much work and money you want to spend I guess. Good luck. 

4
looks good. Have a question though. How does this seal the crack? Is epoxy still needed to seal from leaks and the pins for strength?

5
step by step details would be great.

6
Good luck on your repair. I had a small crack or more like a imperfection on the rear of my cylinder head that would ooze coolant that i ground out and used JB Weld and its held good. Stopped the leak. Also used it on a cracked case of a 4 wheeler and its still holding today and that was a bad oil leak. Trick is to get it clean and scratched good for the stuff to get a good grip on. Your method is probably much better. Hope it does the job for you.

7
My first neoprene seal worked great for about 20 miles. Then the oil would almost run out when hot. Some of the seals were made wrong from what I understand and would groove the crank or just fall apart. I found a man that had the right ones but can't recall his name. It performs well. Just a few drips now and then.

8
I have done mine twice now Tim and still have a few drips but nothing serious. Never tried the rope though. I forget where the last seal came from but it's much better than the first one. Also my crank had some pitting but i took care of that the last time. Just how bad does it leak?

9
I would do away with the external ballast. Just get a coil with internal resistor and eliminate that problem. A early 70's model chevrolet coil will have a internal resistor and cost about $20 and works great with a 3 wire alternator.

10
I got the little red bulb from Advance Auto designed for about a 3/8 dash hole which I had beside the speedometer for the charge indicator light. I think the hole was originally for the gauge lights, external. Like you said, it lets you know when it's charging. Turn on the key, it's red so you know you have power. Start engine, if charging, goes off. Nice set up.

11
I used this page when I rewired my 3A with a 3 wire alternator.
http://www.how-to-build-hotrods.com/hot-rod-wiring.html
It's simple and easy to understand. give it a look, has various wiring topics including using relays fr headlights, horn, signals and everything you will need.

12
Congrats Mark, glad you got it going. Glad you were persistent. That's what it takes.

Ron

13
Pull the distributor cap and check the distributor shaft for to much end play. Bring your points up on high cam like you were setting them and then grab the top of the shaft where the rotor is and see if you have any play. If you do you will notice the points opening or closing out of spec. I had this problem twice and went to a bronze oil-lite bushing and solved thee issue. This can definitly make it run erratically. Also the coil is cheap so try it. I would get an internally regulated one if you're running 12 volt and do away with the ballast of you have one. Ballast can overheat and go bad also. I use a early 70 model chevrolet internally regulated. However I just switched to Hot Spark electronic distributor module using the stock distributor and had to get a coil that measured 3.0 ohms or higher. Auto Zone has one of those if your planning electronic. I can get you the part numbers if interested.
Ron

14
I have been there with the coil myself. Drove me nuts. Just last weekend went for a short ride and the Jeep has been runnung great and it started to miss. The more I drove the worse it got until it would not even idle. managed to make it to my daughters only a few miles away. Checked all I could field testing, reset points,  and found nothing. Got my truck and trailer and brought it home. Pulled the cap off and checked the advance and pulled the points. Seemed the points were only firing on a small part on the side of them. Looked like the arm was sorta bent to the side. Replaced them and it ran fine again. So i ordered the Hot Spark electronic ignition, Starts better and it idles flawlessly now. Can't say I notice any difference in power but it seems to just run smoother. Cost was about $64 for the module.  No more points, condenser or checking timing.

15
I would contact the seller. He is a good guy and see what he recemends with this pump. My pump did not require one. I thought at first it was bad because it gets very little fuel in the bowl. I contacted the seller and he said that was normal and it works fine.

Pages: [1] 2 3 ... 16