The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - OkieFarmJeep

Pages: [1] 2 3
1
Re: seller in Turkey-  I purchased a NOS ring and pinion and it was a good transaction. Part was true Willy's NOS and even with the high price to ship to the US it was cheaper than Omix stuff.  Arrived fairly fast for overseas shipping.

2
Younger years....learning a lot wrenching on that little British car....makes you appreciate the Willy's jeep just that much more. 

3
Bretto- BRM (Brush Research Manufacturing) the people that make the popular hones often called "Dingle Berry" or "Flex Hones"  say its ok and actually sell hones for brass, bronze and other soft metals like aluminum.   I am no metallurgist but I have honed brass many times on other projects- like an old MG midget and it went on to run many thousands of trouble free miles before I parted with it.  Again- I'm no expert- just pointing out that some "experts" say its ok.   So long as it was cleaned well, I would have no problem doing it again.  We sometimes do things on the "farm" that I am sure some professor of something somewhere would tell us its wrong to do, but we get the job done and keep on working  ;D. 

4
I feel like the exception because more people opt for POR or other specific made products BUT I cleaned my frame, axles etc. and then painted it with a high quality OIL BASE PAINT.  It was advertised as made for pump jacks and farm equipment.  Thick as snot but laid down nice with a small foam roller.  Nine years later it still looks great and no rust.  Way less expensive and easy to touch up if I need to but so far no need.   Attached pic you can see the overall appearance 9 years later.  One reason I did it that way is at the time I did not have access to a paint booth and did not want to spray in my garage.  I would not hesitate to do it again- even though I now have access to a paint booth so that says something.

5
I use a zddp oil additive in the crankcase and lead substitute along with a little mystery oil in my fuel, always real gas.  If you had hardened valve seats put in you won't need lead replacement.  The zinc addition is mandatory imo due to flat tappets but there are those that run nothing extra. 

6
I have to really push hard and fast in on the foot starter and it spins right up BUT if I get lazy and don't, it will grind. That usually gets the right amount of push from me really quick as I hate that sound.  I have looked at my linkage and everything looks good and tight- not worn out.  I too don't really want to loose the "kick" starter.  The old way is a pain but it is also a "cool" factor in my book.  Plus most people have no idea how to start it! ;D

7
Austin- Also remember that these flat tappet engines need more protection from cam wear than does a modern roller cam of todays cars.  Choose an oil with a high level of zinc, especially for break in.  It is being removed from todays oils due to catalytic converter issues- something you don't have to worry about on your old Jeep. 

8
Tim- thanks for that info.  This we may never know! The jeep was purchased new by my grandpa in Iowa.  It had the earliest model Auburn Jeep a Trencher and was used on the farm in Iowa and never tagged.  When I inherited it, it came with all kinds of old paperwork but no title.  I had to go through Iowa DMV and get a search done, take that paperwork to OK DMV along with affidavits / the will and OK issued me a new original title.  OK DMV physically inspected it as well and it still has the original body tag VIN which is 452GB119026.  SO..there is the rub- the engine SN number stamped (3J119057) is not the same as the Body SN which is what I would have expected it to be if they had an unmarked block and wanted to just stamp it with something.  It would make no sense for the family to just arbitrarily make up a CJ serial number that is not the same as the body.  But I read that the factory had a skew of numbers... but this is supposed to be a replacement engine..  Strange! :o  Thanks again for your input. 

9
Against your examples, the stampings on my block don't look close.  I called my uncle and asked him again.  He said he knows in the late 50's they put a new engine in it.  He said they ordered it and it was supposed to be brand new and was in a crate when it arrived.  I asked if he knew where it was ordered from- he did not recall.  Asked if they (he or grandpa) would have stamped a SN number on it, he said no.  He did say he was surprised at the long stroke for the little pistons- ChaChing- that tells me they had it apart for him to know that.  Again, leads me to think they got a short block and put the rest of the 3A parts on it.
Not knowing the history like you guys do- why would Ford NOT stamp a block they made? When in the build process were the numbers applied?  I know there was a skew in engine to VIN numbers at one point.  Maybe as Scoutpilot suggests, there was a point of excess engines sitting and that those would have been stamped only when needed?    If the short block was ordered from Willys could they have stamped the number on it for the vehicle it was going in to?  I know at some point they put a replacement serial number on them... could this have been before they standardized that?   Its a puzzle for sure.

10
I seriously doubt that anyone in the family stamped a sn on it.  They would not have cared about that back then.  This was a farm jeep.  Grandpa took good care of things.  I wonder if a Willy's dealership might have?  Bottom line is it has a 3A type serial number and no GPW sn.  The block lower internals are F stamped GPW, the rest 3A.  II am more curious than ever.

11
There is no other number, here is a photo of the boss you asked for.

12
Main bearings:

13
Parts arrived Friday so I flipped the springs and its going back together.  Here is the bock GPW casting and the Sn from the top. Also it has 3A timing gears. So a replacement bock and crank makes the most sense except for the sn number.

14
Parts arrived last night- I decided to turn them over.  What a PITA to get those little keepers off and on again!  Two new valves in- all valves lapped.  Going to get it back together today!

15
And the questions continue.  The block is a GPW casting with F marked main bearing caps.  However the head is not F marked.  Starting to think my uncle's memory is failing and they got a short block.  That said, the sn on the block looks like an early cj3a.  3J119057. Lastly, the heads I am seeing on line all have valve (tappet) clearance cast into them. Mine does not.  What's up with that.

Pages: [1] 2 3