The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mbullism

Pages: [1] 2
1
Forgot to mention...

Your engine serial looks like a Kaiser Henry J version of the L-134.  I don't know much about them.

X2  :)

2
Engine compartment / Re: Pre oiling engine
« on: February 14, 2020, 09:07:56 AM »
Man, I never heard of anything like that.  What would be the point...wouldn't the Vaseline inhibit the flow of oil quickly which is what we want?
without something more viscous than air in the pump, the gears just spin...the pump is not self priming.  The Vaseline is thick enough to allow the pump to "suck", provides a minimum of lubrication, and melts at very low temps so it does it's job, melts, and gets out of the way.  Think of it as assembly lube.  Grease is not recommended since at start up temps it can block small passage ways and take time to clear waiting for operating temps (and even then maybe not).

I've used the Vaseline  and the syringe methods both with success, fwiw.

3
Your CJ-3A Project / Re: "37751"
« on: December 18, 2019, 06:20:05 AM »
  Three years later I am circling back to start doing something with it. 

Every time I think I'm "out", They PUuuuuuullll me back "in"  ;)

4
Buy, Sell, Trade / Re: Late L134 engine, Free
« on: December 01, 2019, 10:44:23 PM »
Hey, Dave.... much appreciated.  Going to soften it up some before getting physical.  Great chatting with you this morning, and thank you for accomodating my schedule  8)

After drooling over your 3A, and taking note of some of the work as you described it I spent a couple hours at various points today reading your build thread....

Gobstruck--->  :o  (Wow!)  Simply awesome job saving her, remarkable work, Sir-

MB

5
Buy, Sell, Trade / Re: Late L134 engine, Free
« on: November 25, 2019, 07:34:39 PM »
email inbound

6
Your CJ-3B Project / Re: End of 3B project
« on: September 17, 2019, 06:54:33 AM »
As long as it's to a good home (garage!)

We're just caretakers, lol

7
Rambling, Malarky, Rants, Etc... / Re: Photobucket alternative
« on: September 15, 2019, 09:25:06 AM »


seems to work  :)

8
Rambling, Malarky, Rants, Etc... / Re: Photobucket alternative
« on: September 13, 2019, 12:16:26 AM »

Also how does one link onto them for forum usage ?

From the album view select the pic and it will open a preview, click on the preview and down to the left will be two tabs.  Select the tab that says "embed codes"... I always go down to "medium image (linked)", hover the mouse over the BB code link and click the copy button that pops up... from there I just paste into whatever forum reply dialogue box i'm editing in.

Been using MWPs since very near the start with zero issues (Thanks, QJ!  :D )

9
The 231 even fire is a great option in a flatty, and a lot of what lets you install a 225 dauntless works just fine (mounts, input shaft, adapter plate, BOP bellhousing, etc.).  Note that while earlier heads will bolt on the water jackets wont line up, so stay mid '77 to 78 and up for parts.  Make sure you get one out of a RWD car.  The FWD stuff was mounted sideways,  has odd motor mounts and I think bell requirements. If possible find a standard shift RWD so you get the flywheel and not a flexplate.  Pretty sure the 231 is externally balanced.

The '77-'78 heads were part of the early attempts at smog stuff and the 225 dauntless got more displacement but couldn't breathe (Small valves) so HP went from 160 in the dauntless to 105ish in the early 231's.  If you find a '77/'78 block with heads, try and source some '79 and up heads with the larger valves.

I'm pretty sure that if you google buick v6 you'll find wikipedia has a list of models to look for... I have one out of a '78 olds omega  :)

10
point well taken,... what do you do when it leaks after you fix it? (my luck)

11
Quote
Wonder if I should do another rear main seal? The one in it is not leaking and I hate to fix something that is not broke. Especially since these newer seals seem to have some issues.

Do you frequently walk up to get in your daily driver and ponder replacing an oil seal that isn't leaking?  ;)

12
That thermostat housing will likely not work very well... measure the engine plate for width at the mounts, at the very least it appears 2A (assuming this is going in a 3A)... no skidplate on the oil pan.  You'll want to drop the pan anyway and just verify it has a floating pickup, at the very least....

13
Quote
Hello Tim,
I read what they said. Seems the compression is the same and the only difference is the bore size of the carburetor is smaller which would restrict HP. I might be getting one of these with low hours so looks to me like just switching the carburetors would do.
If memory serves, the compression is the same but the volume in the head is shaped differently.� You'll typically need a new intake as the bore on the intake will be smaller to match the carb.� There can be other nuances, like the lack of an oil pan skid plate, a thermostat housing that indexes straight ahead... pesky stuff that adds up...

ETA: the one on the left is an industrial head off a pe95 genset, the one on the right a more typical 2A/3A head... I don't recall the casting numbers from here, but there is a difference.  I have no idea what the difference means, though lol.  I'm of the opinion that it makes a difference or they wouldn't have done it  ;)


14
the oil collector is to ensure oil feed to the front bearing on an upslope, and I would surely default to keeping it if I had an open cage front bearing... the sealed bearing (such as what comes with the Novak kit) doesn't need the collector and you could leave it out...IMO

15
Quote
...the engine number is completely different at U52862, ...� If I look at serial numbers online, that would be a 46 model?

Don

It's my understanding that the "U" designation is "utility", used in trucks and wagons... a 46 would be a 2A, and that would start with a "J"

.02

Pages: [1] 2