The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - GlynB

Pages: [1]
1
Thanks for that Tom - I'm not sure I have the nerve to run mine at 200+ it seems a bit rough on a 67 year-old lady! I'm going to try the Water Wetter (arriving Wednesday!) and see what results I get.

Would love to ship my 3a 'back home' one day and drive her along Route 66, but I guess we can dream!

Glyn

2
Thanks for that - I'd never heard of Water Wetter, so I guess you learn something new every day.  I've checked and its also available over this side of the Pond (for about $23.50 incl. postage) so I'll get some and give it a try!

3
"Original"-- Technical Questions, Answers, Observations / Cruising speeds?
« on: September 10, 2016, 02:01:23 PM »
I can drive my Jeep all day long at 30 - 40mph and the temperature stays at 180 degrees or below but if I drive her 'hard' say at a sustained 50 mph, then the temperature begins to creep up towards 200 and I ease off because I don't want to cook the engine.

I've flushed the system and changed the thermostat and water pump so should I just be satisfied with the current situation or is there something I'm missing - like replacing the radiator?

4
Thanks guys

The link is really useful.  I did consider making some wooden duckboards for the footwells and I imagine I could fashion one to extend under the fuel tank - this might also provide a suitable solution.  In either case it looks like an earth strap will be needed to enable the fuel gauge to work properly.

Asking one question seems to raise another - looking at the diagram on the link page and reading aboyandhisdog's post, it seems there is a rubber seal around the neck of the fuel tank? Does this fit on the inside or outside of the tub opening? and how is it fastened in place?

5
..and the new tub.  Bright sunshine makes it difficult to take a good photo at the moment so I'll post more some other time

6
Here's a photo of the Jeep's new tub, plus a photo of the piece of wood on which the fuel tank was mounted in the old tub!

7
Hi everyone

I'm in the middle of test fitting my new CJ3A tub from MD Juan and I'm really pleased with the results.  It has taken a bit of effort to get the wings - sorry, fenders - to line up and I have had to enlarge the holes for the pedals and transfer gearbox levers but otherwise its looking pretty good.

My question is, what is the fuel tank mounted on? In my original tub (which had been patched many times) it sat on a piece of wood broken off - literally - from a 3/4 inch plank.  I'm guessing this wasn't original spec(!) so what should it sit on? I'll post some photos later.

Thanks

8
Hi Tom

FANTASTIC news!  Following your advice I rechecked the number of teeth on my flywheel - it was 124 as you suggested.  I then bought a brand new reduction gear starter from a supplier here in the UK  http://www.demon-tweeks.co.uk/motorsport/alternators-starter-motors/starter-motor/willys/jeep-124-tooth-flywheel/wosp-lightweight-high-torque-starter-motor-denso-type-1-4kw-output.   It bolted straight in place of the old starter - and works perfectly!  I can't believe I struggled for over a year to try and troubleshoot the old starter when such an easy fix was available

9
Hi Tom

Many thanks not just for the advice but also the encouragement.  After 12 months working away in a cramped garage with a leaking roof it gets disheartening when you get this close to the finish.  I have reflected on your comments and will now 1. count the teeth on the ring gear again and 2. based on your comments I have found a race car supplier here in the UK who can supply a reduction gear starter for either a 124t or 129t ring gear for around �165 (or $250) plus postage.

I'll let you know how I get on!

10
Hi Tom

Thanks for your post.  The starter and flywheel ring gear were on the Jeep when it arrived from the US.  They seemed to work OK at first but over 6 months the problems got progressively worse (only engaging some of the time) until now when it won't engage at all. 

Looking at info on the internet I counted the teeth on the ring gear to check it was the correct one for a CJ3A - which I thought, at 129, it is?  I have been unable to find a part number on the starter.  It just says Autolite and just visible is a stamp saying rebuilt and the figures 9 4.

GPWs and MBs are more common over here and I think my next step is to visit my WW2 Jeep parts supplier (a mere 230 miles away) to get his opinion.  He stocks starters for MBs but I don't know whether they are compatible with the CJ3A ring gear?

11
Hi Tim

I've had the starter off (more times than I can remember) and, as I said, the arm on the top of the starter moves the starter gear along the shaft with no problem.  The difficulty appears to be that the starter gear sits alongside the flywheel OK it just doesn't sit close enough to the flywheel gear to mesh?

It's driving me nuts and I'm reluctant to import a new starter from Kaiser Willys or similar because shipping and import taxes will triple the cost - and it may not even solve the problem.

12
Hi All

In the final stages of completing my restoration and went to start the engine today.  The starter gear moves up to the flywheel gears manually, using the starter foot pedal, but just spins without engaging on the flywheel gear. 

I know the flywheel has 129 teeth (I counted them last year) and the starter 9 teeth and there is only minimal wear on both.  Somehow the two aren't lining up properly - anyone any ideas?

13
Rambling, Malarky, Rants, Etc... / Re: Previous owners of my Jeep
« on: June 08, 2015, 06:00:35 PM »
Thanks for the tip about the vin search - I'll give it a try


14
Rambling, Malarky, Rants, Etc... / Previous owners of my Jeep
« on: June 07, 2015, 05:26:42 PM »
My Jeep was imported into the UK 2 years ago but I'd love to try and find out something about its history, who the previous owners were and what it was used for.  In the UK you can apply to the government licencing authority and they will provide a list of former keepers - complete with addresses. 

I gather this isn't possible in the US, but can anyone advise how I might trace at least some of my Jeep's history?  The only information I have is the windshield sticker issued by the West Virginia Police Department, which I assume is some sort of road worthiness certificate similar to our Ministry of Transport or MOT Test certificate?

Thanks!

15
Once You've Joined / New member from Great Britain
« on: April 21, 2015, 04:23:14 AM »
Hello there

My name's Glyn Bryan, I live in the UK and now own a genuine 1949 Willys Jeep that was imported into Britain in late 2013.  As a boy growing up on farms I have always been used to Land Rovers but over the years have also owned a Japanese Daihatsu Jeep and a Korean Ssangyong Korando - a diesel-engined CJ5.

I think the Jeep is brilliantly engineered and am hugely impressed with the quality of the steel - the old body had led a hard life and was due for retirement but when I removed it from the chassis I was impressed that a 65 year old chassis only required a wire brush and some fresh paint.

Am currently trying to line up a replacement MD Juan tub on the chassis (not too easy!) but am out of action for a while as the tub dropped onto my foot from around 4 feet up when it fell of my chain hoist!

Will keep my Jeep red (originally it was Olive Green) as almost all the Jeeps in the UK are either MBs, GPWs or French-made Hotchkiss painted to look like WW2.

Pages: [1]