The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mrman5917

Pages: [1] 2 3 ... 6
1
Thanks for the encouragement guys, I'm going to see what I can do about putting one up in my garage. I like the idea of not building a frame outside (it gets REALLY windy and dusty around here). I should be able to move my car out and get about 2 cars worth of space to work with. Now I've just gotta finish cleaning up the frame and then buy some paint and guns.

I'm thinking now that I'll go with 1 qt of Mastercoat Silver and a quart of Mastercoat Tractorkote. I'll talk to my father in law next weekend to see about borrowing a gun, otherwise I'll stop at HF and pick up the duo. For something I hadn't even considered doing myself before, now I can't wait to do it.

2
Thanks for the reply guys.

Mark - I started using the syran wrap after the first can didn't get quick a good seal on it. Made a huge difference. I'm using the little mini 4 oz. cans, so I doubt there is a pour spout that will fit on those little ones.

Tim - Would you recommend the 2-gun kit specifically for the 1.2 mm nozzle on it? Aside from the gun, anything else I would need to get to make it work properly?

George - Sounds like a quart of primer and a quart of top coat are what I'll need. That helps me figure out how cost effective it will be to build a paint booth and stock it up :)

How much room around the frame should I have? I don't know what sort of distance I would need to have from the "wall" and the frame with regards to holding the gun and having myself in there.

3
Were the plastic sheets just the large painter's tarps you can get on the cheap?

What about getting a HVLP gun from a place like HarborFreight? I'm going to see if my father in law that used to run a body shop has a gun and some expertise to share with me, but if he doesn't have a gun available, are these any good for something like a frame job? Any idea how much Mastercoat and black I would need to sufficiently cover a frame? I imagine it wouldn't need much...

4
I'll certainly take a look. Living in the Mojave Desert of Southern California, humidity and moisture are probably even less available here :)

I'll give it a look though. I've got a bit of cleanup left, but I think I should get the frame finished before finishing the front axle. If I take the from axle off of the bench now, I'll have no place to put it but under a frame that still needs paint :)

5
Tim, that's the first I've heard of it. I take it Mastercoat goes down, then paint with whatever for the desired finish? I've become pretty good at using POR15, but one complaint I have is that if I start with more than just a little bit of paint in a container, but the time I get to the other side of the axle, it's started to dry to the point where it doesn't go on quite as smooth.

After painting my front axle this past weekend, the driver's side is perfectly smooth and looks fantastic, but the short passenger side that was done after the differential case, looks more like alligator skin now that it's dry. It'll work fine for what I'm doing since I'll be adding a second coat and a shot of rattle can Rustoleum for the look I want, but it makes me wonder what would happen if I tried to do a large project like a frame over a period of time. I am using the smallest cans of POR15 I can get and pouring a very small amount into a second container, but if I had to do even less at a time and constantly go back to open the can, it'd take me weeks to do something the size of the frame to get a consistent coat, let alone 2.

6
So if I go POR15, it's just straight POR15 then a topcoat for UV protection. If I go with something like Eastwood Chassis Black, prime then paint.

Has anyone used the POR15 Chassis Coat product? Looks like POR15 can be used as a primer for rust encapsulation (not that there is much left:) ) and then Chassis coat goes on top. Seems like an easy process to complete...

7
What about types/brands of primer and top coat? One easier to do with limited space but lots of time over the other?

8
Hello everyone,

I just got my frame back from the sand blasters, and I'm wondering what I should do about painting, specifically if I should do it my self or send it out to be done. I've got to clean up under the outriggers and remove a few more misc parts, and maybe clean up a few areas that were missed in the sand blasting process, but other than that, I'm ready to go.

I don't have a real way to do a paint booth and spray it myself, so rattle can primer and maybe brushed on POR15 with a topcoat or Eastwood Chassis black was what I was considering.

What are your thoughts and what have you done with your project?


9
Ok, I only had a few minutes to work on the Jeep this weekend due to homework for my Masters, but...

I was able to push out half of the U-joint today and got the shorter axles haft half disconnected. It required a bit more force than what I anticipated, but right before I got to the point where I was going to stop, it started moving and things were great.

After that success, I tried doing the other half. While the picture I had above shows what looks like a crooked cap, I'm not sure that's the case. The material that holds the cap in is thinner on one side than the other, so I think that may be creating a sort of optical illusion.

In any event, I tried pushing and banging and all kinds of persuasion and was unable to get them to budge, even a little.

Is there another method I can use on these to coax them out?

10
I'll have to give that a try. I had given it a few taps after I realized that it wasn't moving, but it didn't really move much if at all. I'll try a little more persuasion next week, or maybe after work one day this week if I get home early enough. I'm assuming if it got wedged up there, I should be able to get it unwedged.

11
I'll try putting the joint back together when I go back out to work on it next weekend. I don't recall hearing clicking noises front he front axle, though the rest of the jeep was making lots of little noises so it may have been disguised. Is there a definitive way of determining if these should be replaced or not? I don't mind purchasing a new set of axle shafts if it's necessary, but I could obviously spend that money on other parts if it isn't.

I pulled apart the drivers side knuckle today, and lo and behold, I have a Spicer style on that side. Aside from there not being a snap ring on the end, this one at least had the shims on the top king pin cap versus the other side having them incorrectly installed on the bottom.

One thing I am having trouble with is getting the cross removed. I removed all 4 of the inner snap rings, but I can't seem to get the caps removed. I tried pressing them out (using the vice and two sockets method) but it seemed like the pressure I was putting on it was too much for it not moving at all, so I backed off. I also tried to just push the cap out from the inside of the joint thinking hat maybe they only moved one direction, but that didn't seem to work either. Is there a method to removing these, or do I just need to put a little more pressure on them?


12
I haven't re-assebled it yet, just took it apart. I'm just curious if, despite what the service manual says, if it really is possible to "disassemble" the joint while the knuckle is still on.

The pin is still in place at this point, and wasn't removed prior to taking apart the joint. I'm starting to think that shouldn't have happened since it appears from the Vernco site that extending the pin into the center ball is the final assembly step, so I would assume you'd have to start by retracting it to start the disassembly?

13
Hello everyone,

Today I took apart the passenger side knuckle on my 1950 3A. To recap, my front hubs are/were mounted behind the drum (the front drums come off freely with only the wheel removal), the axle shaft ends look to be factory (or at least machined) with no threaded ends. My understanding was that the Bendix style joints were replaced in favor of the Spicer style joints, so I guess I'm a bit surprised that I have the older joint with what at least appears to be a later axle shaft. Or were the threaded ends dropped before the Spicer joints replaced the Bendix?

In any event, I just read through the Service Manual and it states that "The universal joint cannot possibly become disassembled after it is installed in the vehicle." But, while moving the knuckle around to remove the bolts from the king pin bearing caps, the axle shaft came out when moving the knuckle from what would have been a left turn to straight on. I haven't measured the diameter of the ball bearings, so I don't know if those are worn down (they don't look worn), but the joint itself looks relatively clean.

Is this something to worry about?




14
The rear axel had been redone prior to me getting it, so I just changed the fluid and cleaned the outside for paint. I originally decided on going with the 11" drums, but I decided to stick with the 9" drums since I won't drive it much and I already had them.

I just started working on the front axel after finishing the rear. You can see what I came across on http://kurtisfranklin.com if you're interested.

15
Mine is slightly later in the 1950 model year (Augustish), but still early enough to have a Dana 41 rear instead of the later Dana 44.

Pages: [1] 2 3 ... 6