The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - SteveZ

Pages: [1] 2 3
1
"Original"-- Technical Questions, Answers, Observations / Re: Hand wiper
« on: February 18, 2014, 08:45:18 AM »
Quote
Mac,

I bought the repro hand wiper for the 2A and did what you did...added to the length of the arm so it reaches the 3A windshield.� I looked through my Photobucket stuff, but couldn't find any real good close ups of the hand wiper.� Here is one of the inside.

If Nate's link didn't get you what you're hoping for, let me know and I'll snap a few close ups tonight when I get home.

Tim



 


Not to derail the OP but wow! What a beautiful dash! It looks perfect!

2
"Original"-- Technical Questions, Answers, Observations / Re: Fun stuff
« on: February 28, 2014, 01:54:22 PM »
I can remove the one on the cover no problem. It's the drain plug on the bottom that I can't get out.

3
"Original"-- Technical Questions, Answers, Observations / Fun stuff
« on: February 28, 2014, 06:37:45 AM »
Well, not really. I still have brake issues. Seems the PO used whatever brakes they could throw on and get working. Trying to locate parts that match what was on there has been quite an issue and expense.
I've had to deal with the stuck drum on the front which required a 12 ton hydraulic puller to remove and destroy. Once I get the brakes addressed and correct them it is time to move on to the rear differential drain plug that will not come out. Nothing remains of the plugs recessed head to remove. Drilled a hole and tried the largest easy out I could find and it won't budge. Kind of like that 70's GMC steering wheel that refuses to come off and bends grade 8 bolts like butter when using a wheel puller. I swear this thing is cursed. I'm beyond frustrated! Fun times, fun times.....
Anyone in NE Ohio that likes beer?  :P

4
Yes, it has a breather.

5
Pic of front Diff. Is this a 25?

6
Quote
Hi Steve,
The axle in the photo is a Dana 41.� Your front is probably a Dana 25.

Tim


If I take a picture with the cover on will you be able to identify it or should I remove the cover and take a photo?

7
Quote
The tag you have (43 over 8) refers to gear ratio. 5.37 gears

Excuse my ignorance but how does that translate? 43 over 8 to 5.37?

8
I filled them with kerosene and let it run for a few minutes then drained. The front diff has a tag with a 43 over an 8 but I can't find anything on the rear differential.

Here is a picture of the rear with the cover off.
Can anyone tell me what I have? Both front & rear?

Thanks.

9
While I have this on jack stands I figured I might as well flush out the trans, transfer case and differentials.

I intend to pull the differential covers and replace the gaskets and clean them up a bit anyway.

My question--- is it safe to flush all of them with kerosene or would a light motor oil be ok?

My Forum search nover oulls up any results when I search for flush or flushing.

10
I just got done mixing my own "pudding" for future use. Mobil1 Gear Oil and Mobile1 Wheel Bearing Grease. I purchased a grease gun with a Seal Off adapter fitting specifically for using this on the knuckles and sterring box.
For my "pudding" I used about a 60 grease/40 oil mix.
The 140 leaked entirely out of my steering box. Hopefully this won't.
I saw the Lucas Oil Hub Oil. It did not appear thick enough. The STP Oil Treatment is like molasses. I wonder if that would work? For now, I'm going to stick with the "pudding"

11
Thank you

12
Went back out and looked. Of course I found them.
I threw some 140 in it for now as they were damn near empty. I'll get the Napa for the next fill.

Thanks for the quick reply.

13
Where is the fill hole? On the backside? I've read about lubing with a "pudding" mixture but been in detailed schematics I don't see where to fill them. I must be overlooking the obvious. What type of filling plug is it so I can identify it.
I know it's a stupid question. But I've searched, checked my manuals and even the steering knuckle schematic with no mention of a fill hole. Do they have drains too?
This can be lubed without tear down correct?

Thanks & sorry

14
The horn cover part number comes up as a 74-75 GMC.

I am still unable to remove the wheel. What am I missing? I took the nut off but this collar seems to be holding it on?

More pics.

15
Here are some more pictures. Unable to identify what these wheel/column came out of to look for rebuild kits or wheel replacement.


Pages: [1] 2 3