The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Steve R

Pages: [1] 2
1
BODY and trim / Re: Floor Mats?
« on: January 08, 2020, 08:20:32 PM »
Thanks. I will take my worn out mats and look for something close.

Steve

2
BODY and trim / Floor Mats?
« on: January 08, 2020, 01:56:08 PM »
Has anyone found a good source for CJ3A floor mats. The ones from my previous owner are disintegrating and I can't find any replacements on-line. Know there are probably some made for something else that will fit just fine... just don't know what they are.

Steve

3
Mine used to immediately go back in when you let go of it. Changed it to one that locks when you twist it. Couldn't see the point of the ones that pop right back.

4
Anyone tried the French new Carter W/O carb yet? 288 Eusos sounds pretty good. Can't copy and post but should be easy to find at JeepEST.

5
"Original"-- Technical Questions, Answers, Observations / Re: Gas Cap ID
« on: December 28, 2016, 09:36:02 AM »
I am on the third replacement cap for my 3A. Napa, Auto Zone, and now Walck's. The Napa one fit but leaked, the Auto Zone one wouldn't go on. Walck's fit but leaked when on an incline. I have gone to buying the replacement gaskets for a Jerry can on ebay (the filler spout ones). These fit and stop the leak but wear out over time.

6
I "second that emotion" as they used to say. Tell us more. Many of us want to keep the old engine but want more power. At least 20 or so HP..

7
"Modifications"-- Technical Questions, Answers, Incites / Re: Dual carbs
« on: November 20, 2017, 05:48:32 PM »
Lost something. As I was trying to say, I am sure there are a lot of us who do not want to replace their go devil engines but want some more power. What do you recommend?

8
It is two year later. Does it still work? Have you made more? Will you make more? Am sure there are a lot of us who want some additional power but don't want to butcher their Willys.

9
EVERYTHING ELSE, General tips / Re: Winch plate and winch wiring.
« on: February 17, 2018, 04:34:18 PM »
Previous owner welded a 1/4 plate between the frame rails. Had a 5000 lb Badlands on it. Just had a Smittybuilt 9600 installed in its place. Haven't used it but it certainly fits.

10
Engine compartment / Re: water pump performance?
« on: December 23, 2017, 04:11:43 PM »
Don't see that you have tried replacing the water temp gauge. I went nuts trying to figure out my overheating. Took it to an old time radiator shop in Winchester Va (they had an old Jeep Tuxedo in a corner of the shop). They did a drop test (see if the water runs out of the radiator fast) and showed me the temp readings at the thermostat housing ((165) and at the top of the radiator and bottom. Told me the gauge was bad. Changed the gauge and overheating went away. I was surprised in earlier change outs of thermostats at how rusty the thermostat retainer was. Changed that out the last time I changed thermostats. Good luck...

11
Engine compartment / Re: Wiring for test start
« on: February 06, 2016, 05:55:04 PM »
Might suggest that you check the float level in your carter carb. Mine leaked gasoline and a local jeep dealer said i needed a new carb. Scout Pilot refused to sell me a new carb and guided me through an adjustment process. I set the float to the correct level and no more leak. Has been running great ever since. Good luck.

12
Chassis, brakes and suspension. / Re: Brake Upgrade for CJ3A
« on: July 29, 2018, 06:38:15 PM »
Not that I wouldn't like 11 inch drums or discs (lean toward the 11's for appearance) but I am pretty much happy with my "new" brakes. Bought NOS shoes off ebay and took my mechanics advise to send the shoes to Rochester Brake and Clutch to put the softer brake shoes used by old car restorers to improve stopping power. Won't last as long as the usual replacement shoes but I'm lucky to get a thousand miles a year on my 51 3A. Just a thought and I spent my money on gears instead.

Steve

13
[/img]Thanks. That is one spotless undercarriage. Just got back from a machine shop that has my trans and transfer case. Had a 46 2a (column shift).  Crawled under it to see the emergency brake hook-up and looked at the firewall. Think I get it now.

14
Thanks, that helps. I think there is an initial mounting and clamp on the firewall next to the air cleaner but I can't figure out just where it is (I have.... unconnected... what looks like the clamp sold for this at several places). Also curious about the length of the return spring at the transfer case brake. Seems like it must be around 18 inches long and that can't be right. W

15
Does anyone have pictures of the emergency brake cable brackets/clamps after the cable comes through the firewall? Would love to see what I am missing and how to replace it/them all the way to the brake at the rear of the transfer case. Can't find this anywhere else. thanks

Pages: [1] 2