The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - PeterL

Pages: [1] 2 3 4
1
If the bores are indeed round as he said, sleeving and grinding is pretty normal.  Honestly, whats not normal is for the housing (cam bores) to be "round" if they are worn.  Let me know how it works out!

2
Cool beans, if they have a history of that type of repair I am all for it.  I only made my recommendations on the basis that the machine shop had not made a similar repair before. 

Good luck!!

3
Glad I could help.  I am a Reliability Engineer, essentially my whole job is to systematically pick apart things to find out how/why they failed and how to eliminate that mode of failure.  I did not want to pull my engine this summer and not know what I was getting into, so I thought long and hard since October about what the problem could be.  I am glad that you have confirmed the problem.
Again, there are a bunch of different ways to repair it. I myself like simple/straight forward approaches.  I strongly feel that cast iron sleeves shrunk in with Liquid Nitrogen are the best most cost effective solution.  Keep in mind yes, for years and years interference bushings were pounded in with a hammer but, liquid nitrogen will keep the fit concentric and ensures you that the oil port will line up exactly where it needs to go.  Oh and one last thing, you can get one hell of an interference fit (they will never come loose EVER).

 Keep me informed on what they do for the repair!

Peter

4
Another piece to think about.  When you do research you can find references on the web Cj2A website and other places on how to install a bearing into this location.  It is possible but, if you do find you need this repair I recommend a different repair.  Have your machine shop line bore the 2,3rd, and rear bearing housings to accommodate new cast iron bushings.  They are cheep $15 or less each and you can predrill the hole for the oil port.  The labor to perform the task will be less than trying to retrofit a bearing assembly.  If the machine shop does it right and sets the bushing up with a 0.001-0.002" (OD) interference fit and they shrink it with liquid nitrogen, it will slip right in and within seconds it will warm up.  No locktite, no beating with a hammer, and no special pulling tools in awkward positions and it WILL NOT come out.  The fits will be restored to factory, with the same material, fit, and finish.

This is the company I used to use when repairing bearing fits in my old shop.

http://shaverkudell.ca/wp/products/eze-sleeves-list/the-original-cast-iron-series

-Peter

5
Sorry computer glitch- My thoughts continued.

One thing to remember, oil pressure does not equal flow.  I believe I have enough oil flowing.  But somewhere in the system there is a gap that would have gone un-repaired or un-machined during my rebuild.  The only thing that fits this would be the rear Camshaft housing at the rear of the block.  The front housing contains a bearing and is easily repaired by boring and bushing.  However, the rear housing is cast iron and a part of the block.  It is not easily repaired.  This is likely the only thing, due to location and a lack of replacement parts that was left untouched. When did measure it it was .006-.008 out of round.  I did not think this was too awful a the time but I am convinced that at low RPM there is enough bleed by to reduce the oil PSI to near 0.  While at 2k RPM the PSI is 22.  I would bet $100 bucks, that if that was bored and bushed to a 0.001-.002 tolerance my at idle PSI would be 20 ish and at 2k it would be 35-40 ish.

I would bet that you are dealing with the same issue.

Just my thoughts after thinking/checking on mine for the past year. 

6
I rebuilt my engine last year. I am going to yank it as soon as the weather stays above 50 degrees for more than a day.  I suspect the problem lies with the rear cam seat.  Why do I suspect this?
1) tried two different oil pumps - Same result
2) tried two different gauges - Same result
3) I used to work in a machine shop and I am confident it both my initial measurements and my final assembly measurments.
4) End-play was checked and rechecked upon disassembly.
5) I pulled the oil pan last year to check all the galley plugs - all installed
6) removed the front timing cover and inspected the aperture.  I had previously brazed and re-drilled a .040 hole.  I checked with a wire guage all OK.

7
I agree 100% with Jackdog06.

Body is OK everything else is JUNK!!!!!!!!!!!!

8
Way to give us a product update without actually responding to our problems...................... >:(

9
Well, I can honestly say that I am a little irked that when two customers have a problem the response from Rommel falls eerily silent...  Well, as an update I drilled out the spot welds on the fender support channels, and then took my handy grinder out and cut out the entire inner fender on the right hand side.  Yeah, I was angry, but then again, the grinder slicing through my money/crappy fender made me feel much better.  Oh well, I guess I will go have a beer now.  >:(

10
jackdog06,

I also purchased the kit in March and have been dealing with the same problem. I was so frustrated with it I stopped even trying to work on it.  I will get back to working on the body when I don't feel like cutting the fenders in half with a torch....  I contacted OMIX about it. According to all the tags that came on the body they warranty against craftsmanship defects.  Yeah, well they didn't care.  I am unhappy, yet relieved to know it was not just me  :( 

11
Rommel, when will these new parts be available?  I purchased a new tub kit last month and I have been really struggling with the fender fit. Will there be an updated part number to order the "new" fender?

12
Ryan,

Thanks for the fast response.  This isn't exactly it but, I think it will do.  The instructions I had began by telling you to start the jeep and then go get a cup of coffee.  Once the engine is up to temp you can begin the adjustments...

Either way, I think the referenced instructions will work well.  All be darned, once again Ryan you come to my rescue.  Hope all is well up north!

13
Good evening everyone,

My pc died last week.   I had a link saved that pointed me to very specific directions on how to time/tune your L134 using a vacuum gauge, dwell meter, and timing light.  Does anyone know what I am talking about?   I have spent the last two and a half hours searching for it and I cannot seem to find it.  (yet I remember repeatedly stumbling across the link until now).

Any help would be appreciated!! 

Peter

14
Oldtanker-

If you buy a tub or body kit make sure it was RECENTLY manufactured.  There have been quite a few changes and if you get one that has been lying around it is a PITA.

TRUST ME!

15
Well, the tranny is apart.  The main gear synchro was broken.  Also upon further evaluation it looks like the input shaft and the main shaft did not have enough end play.  The main shaft shoulder where the needle bearings are wore away into the input shaft. I have reviewed all of my documents and I cannot find any sort of reference for overall mainshaft/input shaft end play.    :(

Pages: [1] 2 3 4