The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Wylde

Pages: [1]
1
"Original"-- Technical Questions, Answers, Observations / Re: T-90 transmission Front out put shaft Question
« on: October 19, 2012, 11:53:12 AM »
Ok, thank you so much....

Looks like I am good to go with tranny questions.

Thank you so much for your help.

2
"Original"-- Technical Questions, Answers, Observations / Re: T-90 transmission Front out put shaft Question
« on: October 18, 2012, 02:26:06 PM »
Ok have the felt washer.....no ruber side!

How does that felt washer sit? Does it sit in the tube of the plate or next to bearing?

3
"Original"-- Technical Questions, Answers, Observations / T-90 transmission Front out put shaft Question.
« on: October 18, 2012, 09:42:13 AM »
Ok, new question for the T-90...

I have every thing built and bolted up to the Engine, the body is not yet on the Jeep....( Pics of tub on jeep for fitting of body to frame only ).
before I mate the body to the frame, I want to put to bed any bugging questions, while the Body is not yet permanently on the frame for good.

My question, on the front of the T-90, the front Bearing and output shaft, retainer... is oil allowed to flow past the front bearing, between the retainer and the transmission its self?

I see there are one or two ports below shaft, looks like oil is allowed to flow back into case... if this is the case, what prevents oil from running out of trannsmission from the front shaft and all over the clutch?

4
"Original"-- Technical Questions, Answers, Observations / Re: Aft T-90 Bearing Question.
« on: October 18, 2012, 09:24:32 AM »
Thanks, that does explain and answers my question.

Thank you all for all your help.

5
"Original"-- Technical Questions, Answers, Observations / Re: Aft T-90 Bearing Question.
« on: October 17, 2012, 04:18:34 PM »
follow up question.


Ok So no oil Seal, No Oil Slingers on rear bearings.

So there is no problem with transmission oil flowing into the Transfer case, and vise Versa?

Thanks for the response.

6
"Original"-- Technical Questions, Answers, Observations / Re: Aft T-90 Bearing Question.
« on: October 16, 2012, 04:31:42 PM »
do you have a link to a similar pick, showing the slinger ???

also what slinger for what shifter?

7
"Original"-- Technical Questions, Answers, Observations / Aft T-90 Bearing Question.
« on: October 16, 2012, 02:32:48 PM »
I have a T-90 and related Transfer Case for my CJ3A. Have assy and installed. ( HAVE NOT RUN YET )

I have a buddy who has a GPW, I was helping him put his Tranny and Trfr Case together, as we were putting the two halves together I noted he has a seal around a Washer just forward to Aft Bearing, as well as two Oil Slingers forward and Aft of the Aft bearing.

My question, with my rebuild kit, drawings, and maint manuals did not show these items on my build up.

DID I MISS SOMETHING? or does the CJ3A differ in which that these items were omitted and not needed?

any reply an insight would be great. Thank you.

8
Once You've Joined / Re: Wylde from Kernersville North Carolina, USA
« on: October 18, 2012, 02:35:42 PM »
That is juans red special jungle primer.

Going to sand it down anxd re do it....shop air on places has blown the primer away from un preped metel.

Three step prep......acid etch green, then red ox primer, then two coats OD 33070

9
Once You've Joined / Re: Wylde from Kernersville North Carolina, USA
« on: October 17, 2012, 04:30:58 PM »

http://www.facebook.com/photo.php?fbid=152746201472262&set=a.152746148138934.39546.100002106490689&type=1&permPage=1


http://www.facebook.com/photo.php?fbid=109045915842291&set=a.109036215843261.18027.100002106490689&type=3&theater

10
Once You've Joined / Re: Wylde from Kernersville North Carolina, USA
« on: October 17, 2012, 06:27:09 AM »
I think you need to be signed in to view the page.


11
Once You've Joined / Wylde from Kernersville North Carolina, USA
« on: October 16, 2012, 02:42:03 PM »
Hello I own a 51 MB-3A Jeep.

Have been restoring it over the past three years.
Please feel free to check out my Facebook page and pics...

Album #1
http://www.facebook.com/media/set/?set=a.109036215843261.18027.100002106490689&type=3

Album #2
http://www.facebook.com/media/set/?set=a.152746148138934.39546.100002106490689&type=3

Pages: [1]