The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - dodjh

Pages: [1] 2 3 ... 9
1
Carl...what length and width are the straps that were used? I need some and also were did you buy them?

Great pictures and video, just as if I were there also.

dodjh

2
Thanks Carl...I posted on CJ-2A and you confirmed what they were saying.

Charles

3
How do you fill the T.C. and 3sp Transmission?  I read there is a balance betwen the two that has to be met....it was different than just topping them off through each plug.

Am I imagining this?

4
Thanks Larry!

Charles

5
Well...I have all front shoes, W/C, M/C, all new lines and ready to bleed to remove air.

To adjust the M/C how do I know how far out to extend the rod for the piston in the M/C?

Doesn't the brake pedal adjustment dictate how far to adjust the plunger rod?

Thank You

6
athawk11...that is the first one I picked on Youtube and it played 4 1/2 minutes and stopped.  Maybe it will play through this time.

7
Thank you athawk11

8
Does anyone know of a link to show DBL flaring a brake line?

I bought 3/16" line and my old looks like a 1/4".

Also the Hub seal in one Brake Hub is leaking...the Seal # is CR 21101.  Is it suppose to be flush with the outer edge of the inside of the drum...not sunk down in?

9
I looked and found out that on the 11" shoes, the long shoe always faces forward.

If anyone has a comment, please poat it.

Thanks.

10
On the front brakes, does the long shoe face the front or rear?

Thanks

11
Bob...they must have.  Today I picked up two (2) lengths of the,"WORKABLE," steel brake line, 40" lengths. One section for the pumkin

line and the other for the M/C to Tee on front axle tube.

Haven't bent any line in a while!

I should be prettty good by the time I finish the back lines!

12
Bob...Thank you for the post....my set up is like that except the hard line from the M/C has a Hose part of the way.  The hose attaches to the tee.

So, just take the two (2) lines in and have them match them up.  Sounds simple enough.

Will it matter that I'm using Silcone Brake Fluid with the line as far as which line they find?  

13
Hello to all....I reduced my picture size to 134 and still couldn't attach them.  I can't tell you how many times I've written a post and tryed to load

pictures only to have them not show up in the preview or post.

Situation:  I'm unable to get the front pumkin brake line from Walcks.  It runs from the front brake junction block to the Passenger front tire.

                Also, the brake line that runs fron the M/C to the front junction block via a rubber hose line.

I wont need the S loops because of longer front brake hoses recommended by Carl Walck.

I haven't flared or DBL flared any steel brake line in years and what I was flaring, probably wouldn't be called a flare by most of you.

Where can I get the two (2) Lines I need?  The person I usually deal with at Napa wasn't in and the person I did deal with, WASN'T IN EITHER.

(No Disrespect intended)

Charles

14
QuebecJeep...that must be why I am unable to get them to attach.

How do I enlarge the font...I scroll to 12 or 14 and I just get enclosed brackets with the numbers 12 or 13?

Thanks

15
I've been banging my head against a lot of walls lately and know this one.

All I wanted to post was, I received Front Brake parts from Walcks today and the front rubber lines he sent are smaller than what I have now.

Is that a problem?

I took two (2) pictures and cannot get them on this site.

Pages: [1] 2 3 ... 9