The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Macgyver

Pages: [1]
1
I'm going with the T90 and D18, plus a 231 even fire. I'm working on the engine now. Not too radical, but much better than stock. Found some high compression pistons at TA performance (9.5-1) mild comp cam and holley 390 carb. I'm going to port the heads and have the rotating assembly balanced. I found an old jeep flywheel (90lbs) that should work out. I don't get to work on it much because of time constraints. But when I work I like to have a fool proof plan ready in advance. Thanks again to all who comment.

Cole

2
Thanks, for the info. Every little bit of advice helps prevent mistakes. I did my steering and brakes from guys posts on the old cj3a board and I think they turned out real well. The engine height has given me something to think about. Any other gotcha's are appreciated. I'll check out the CJ5 board.


Thanks again, Cole

3
I thought about a better tranny, but the overall lengths would destroy the rear drive shaft angle. I decided on a Warn in the future. I'll probably get the jeep going, then add one later from Herm. I'm rebuilding the T90 and it seems rather stout. �I bought a Warn OD brand new in 1978 for $300.00 and I wish I still had it. �The 4:38's should be low enough I think. Thanks for comments, they keep me thinking.

Cole

4
Carl, Thanks for the offer. I think a V8 would be nuts, but a V6 is a pretty good upgrade. I upgraded the streering and brakes and I think it's going to be safe. Again, thanks for your comments, I'm a little too far along to turn back.

Take care, Cole

5
Thanks, I checked it out and it answered a few questions. I guess I am a little Parinoid about it. I haven't done an engine swap in 20 years. When I was in my 20's I would just jump in and go for it. I made a lot of mistakes back then and had to redo many things. Anyway, I'll figure it out.

Thanks, Cole

6
I'm new to board and I'm going to ask a question thay has been asked many times I'm sure, so sorry in advance. I need to know how far forward to move package forward. Also, how far to the one side do I move it as well. It will be Stock T90 tranny and Dana transfere case, with an Adapter and 231 Buick even fire. I'm getting close on the frame, with the steering getting finished this week. Pretty much ready to go. Any good links?

Thanks, Cole

7
Thanks Nate, is it possible to 180 these pictures for our desktop friends. When putting in the V6 you will need to either remove and replace crossmember or modify. I split and boxed so the mustang radiator will slide lower to line up with front of Buick. This seems to me to be the best way to go. I then tacked on some mounting tabs for the radiator to mount to the grill. Still waiting on my brother in-law to Tig up. I don't get to work on my jeep very often, it's in CA and I live in AZ. :)

8
I tried to repost, but I get a message that the file is too large. I just went straight from my ifon pics from choose file box. Do I need to reformat pictures? It is saying they are 2670k per pic. Sorry don't understand that stuff.

Thanks, Cole

9
Can't figure out how to post pictures. I guess file is too large from my ifone. Any ideas?

Thanks, Cole

10
At the in-laws working on the radiator mount. I forgot that crossmember was in the way, so I cut it longways and welded on a plate. My brother in-law suggested that I weld in additional material below the crossmember to protect aluminum from flying objects. Tomorrow I'm going to tac some mounting tabs on the grill and get my brother in-law to Tig them. I'll try to post some pics. :)

Cole

11
Thanks, ordering one.

Take care, Cole

12
Getting ready to order radiator. What year mustang am I looking for? I am assuming the old ones, so v8 or 6 banger. And how do you mount, should I weld in tabs to bolt to. Do I need to brace with the rods that bolt back to the tub? Anything else you guys can think of would be great.

Thanks, Cole :)

13
Nate, thanks nice fit on the radiator. That's what I will use.

Thanks, Cole :)

14
Thanks for the reply. I placed the engine in based on questions you guys answered last year. I moved transfere case forward and to the right 1 inch. I don't have the body back on yet, but holding the stock radiator up on the mounts seems close. I thought there was some discussion a while back about a shorter pump. Probably with a mustang radiator there will be more clearance. Is there another radiator you might suggest? Also thank you for all your posts, I have stolen many ideas from you.

Cole 8-)

15
Hello, I've been away working for a while. My project has been progressing slowly. I need to know if there is a short water pump for the 231 V6. Napa says no but I've heard it brought up before. If anyone has a part number.

Thanks, Cole

Pages: [1]