The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - WTB853

Pages: [1]
1
In response to your second question, I can't see how adjusting one shoe (front or rear) would affect the other at the bottom adjustment on a given corner. �The bottom eccentrics should not affect each other even though the anchor pins share the anchor plate. �I can, however, see how there may be some feedback between the upper eccentrics via a new, tight brake spring. �(Just my .02) There is not much holding the upper portion of the brake shoes. �If everything was perfectly rigid and there was no slop @ the bottom anchor plate, then no, one upper cam should not affect the other. �However, with the upper cams being inboard of the spring and 4-5" inches from the only solid anchor point, I can visualize how pushing one shoe outward could create a slight twisting effect on the other and moving the backing plate side of the other outward if only slightly. � �

2
I am at the exact same spot as you right now.  I dropped off my block @ the machine shop this afternoon.  It is currently bored .060 over and I have my fingers crossed that the magnaflux comes back clean.  I have been reading up on the "bore vs sleeve" decision and wanted to share a quote I saw somewhere over on the 2a page.  I am paraphrasing but it went something like this...........

"It depends on whether you are building it for the short term or long term;  if you bore the block .080 over and plan to have the jeep 30 years from now facing another rebuild, you won't have the option to sleeve - not enough material left - whereas if you sleeve now, it may be more expensive in the short term, but you will have more options available to you in the long term........"

I butchered it but you get the idea -

3
I can answer a few of your questions, but not all of them.  M38 engines (block and internals) are no different than 3a engines.  The head and all accessories are different, but the blocks are the same.  You can transplant all 3a stuff onto an M38 block.  You want to use a late 3a starter with the 129 tooth ring gear.  M38 starters work with a 124 tooth ring gear and are 24V besides.  The engine serial # in your first picture shows a 3a engine; the idea that M38 stuff is mucking up the works is incorrect.  Your picture shows a 10 bolt flange which should be the 804380 casting that started in 1952ish.  I am not familiar with the casting on the bellhousing and can't tell much about the rear plate, but maybe those are for a 4 bolt flange Lhead (641087 casting)?????   Where did you get the rear plate and bellhousing?

4
I am collecting parts here and there for a second jeep (46' 2A) if I ever complete the first one (51' M38).  Backward logic, I know...............Anyhow, I think a perfect setup (if you are going to move away from stock) is a 225, sm420, D18, Warn overdrive, and stock axles.  The 1:1 4th gear and overdrive still give you decent top speed while achieving a ridiculously low crawl ratio (7.02*2.43*5.38 = 91.77 :o).  An sm420 to D18 adaptor in a few inches thick and will negatively affect the rear driveline angle, but that is a HUGE gear range.  Of course, it all depends on how you will use the jeep and how deep your pockets are..................

That CJ5 site is a good resource for swaps - that is what they do over there................

5
The Novak Adaptors webpage looks like a great resource for the buick 225 swap.

6
I got the same news from the machine shop about the first block I brought home for my project, 4T42063. �I bring it up because I am curious if anyone knows what the "4" stands for. �I was told the "T" in "4T" means it was originally a truck engine, but the "4" ???????

You can always use it as a 4 hole planter and she will continue to bring happiness and enjoyment for all even after her intended purpose has been nullified. �My wife is close to accepting this idea for 4T42063. ;D

Pages: [1]