The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Bedrock

Pages: [1] 2 3 4
1
Tim, I like the way you did your turn signal modification.  Very nicely done.  I might end up doing mine the same way.


George

2
What Tim says is correct. �The quality of the shroud that Walck's offers for the side-mount radiator is outstanding, as is the fit. �I couldn't be happier with mine.



George

3
Tim, that is a very clean and well done installation, as usual.  It looks good. Great photos too......as usual.

George

4
Thank you for the information.

5
I have a 6V CJ3A horn that I would like to use in my '51 3A, but my Willys has been converted to 12V.  Can anyone tell me what would be the proper value of drop down resistor to use to get the voltage down, and where I might get one of these?  I know that some people use a 6V horn with a 12V system with no resistor and are careful how they use the horn.  I would prefer to install a resistor if I can get one.   Thanks in advance.

George

6
"Original"-- Technical Questions, Answers, Observations / Fan shroud
« on: October 05, 2012, 04:56:28 PM »
When I got my 3A it didn't have a fan shroud, and I looked everywhere I could think of to find one that wasn't half rusted out. �As far as I could determine, no one made a reproduction shroud for a side mount radiator. �I had checked with Walck's months ago, and he told me that originals were very hard to find. �Just recently I discovered that Carl has had some manufactured. �I just received mine, it fit perfectly and is really well made. � I am very impressed with the quality. �Hopefully this will be of interest to anyone else who might be looking for one.

7
Great job.  The smiles on the kids faces are reward enough for all the time you spent on the jeep.  Congratulations.

8
Just changed the seal in my rear differential.  The most trouble I had was getting the nut to break loose.  After I finally got the nut off, the yoke came off pretty easily.

9
As Carl said, the threads in the block are coarse, so the use of bolts could change the torque specs as compared to studs, which have nuts torqued onto a fine thread  When I got my '51 3A it had bolts, and there had been a leaking problem.  I took off the head because I wanted to replace the bolts with studs, and there were cracks in the block radiating out from about 5 of the stud holes.  A couple of these cracks had opened up pretty well.  I don't know whether the use of bolts, and then over torqueing, caused the cracks.  Maybe the PO tried to stop the leaking by applying more torque to the bolts.  I ended up getting another block.

My suggestion is to use studs.  That is what was originally used, and I think when in doubt, it is generally safer go with how things were originally designed.

10
I seems worth fixing to me, either by welding or pinning.  If you do decide to have it fixed, I would recommend that you have it sleeved back to standard.  Boring it further, if it is already .060 over, is asking for trouble in my opinion.  Hope it works out.

11
I think one of the left-hand thread shackle bolts goes on the drivers side front, and one goes on the passenger side, rear. �Both go on the bottom, at the spring eye. �I might have to be corrected on this, but that is how I remember it. �If someone has previosly used a right-hand threaded shackle bolt in the spring eye where a left-hand threaded one should go, it can very difficult to replace it with a left-hand threaded one. �I had to use all right-hand threaded shackles on the front of my jeep for that reason.

Hope this is of some help.

12
Finally got the upper right rear shackle bolt out.  Pardon my misuse of the proper terms.  I hope this description is understandable.

To say that the shackle bolt was tight is an understatement.  The first thing that gave way were the welds that held the shackle bolt "body" into the hanger.  After that I had to use a small monkey wrench on the shackle body to hold it will I tried to loosen the bolt.  Then I broke my 12 point 7/8" socket.  I went to a 6-point socket, with a 2 foot breaker bar, and turned the corners off the bolt head.  Then had nothing to lose, so I put a 3 foot pipe wrench on it, and turned half the head off.  By then I was figuring that I would end up cutting the hanger off, and putting a new one on, a job I was not looking forward to. But I was not ready to give up.  I took a 2 pound sledge hammer and beat the hanger open so that I could get the shackle body out.   After I got it out, I put was was left of the bolt head in my vise, heated the body with my little propane torch, put the big monkey wrench on it, and broke the rest of the bolt head off.  You could now look right thru the body where the shackle screws in, and I figured I was done.  I got my cutting wheel ready to cut the hanger off, but had one more option.  I called my welding expert, and took what I had left over to him to see what he could do.  He was making no guarantees.  He took a 5" bolt that fit snuggly inside where the shackle screws in, and gas welded it to what was left of the bolt head, and to the other end that protrudes.  He put it in a huge vise, turned on the welded bolt, and BROKE THE WELDS trying to unscrew the stuck bolt.   Then he arc welded the bolt back on, and broke THOSE welds.  I had never seen anything like this.  He said there was one more thing to try.  He re-arc welded the bolt in, and heated the body until it was tangerine orange, turned on the bolt he had welded in, and finally the shackle bolt came out.  Unbelieveable.

I took the part back home, put it back in the hanger, bent the hanger back into shape, welded the part in with my little Hobart welder.  And, easy peasy Japanesee, I was done!  Only took me 6 hours, over the course of 2 days to remove one shackle bolt.  Happily both shackle bolts came loose easily on the other rear spring.

13
If I made a post for every problem I find with my jeep, as I try to get it mechanically decent so that I can start working on the body, this place would be a lot more active.  I would probably be spending half of every day on the computer.  Today I was trying to remove the shackles from the rear springs.  I thought they would go as easy as the front shackles did.  But, no suck luck. I should have known better.  Can't unscrew the upper shackle bolt on one of the springs.  A 2 foot breaker bar won't budge it......yet.  No, it's not a left hand thread.

Going to get real serious with it tomorrow.

14
Thank you very much for the heads up.  No, it's not too late.  I just ordered the mirror.  Thanks again.

George

15
Thank you both very much for the information. �I think with what you have told me I can put mine on, and it will be satisfactory.

Pages: [1] 2 3 4