The CJ3A Page CJ3B.info

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Ron D

Pages: [1] 2 3
1
BODY and trim / Re: Floor Plugs
« on: September 02, 2026, 08:34:22 PM »

2
There's supposed to be a zerq in the end of it.
Pretty sure the grease zerk on the end of the shifter pivot pin was a military thing not on the CJ's.
Could be mistaken.

4
Buy, Sell, Trade / Re: Seat Cover Hardware
« on: June 03, 2025, 11:16:57 PM »
Answered your post over on the G503 forum same question: https://forums.g503.com/viewtopic.php?p=1994486#p1994486

5
Engine compartment / Re: Engine oil pickup assembly
« on: May 09, 2025, 06:38:45 PM »
Found waxed cotton twine in mine also, but it surely can't be there as a "gasket" as the whole thing is floating or submerged in motor oil.
Why "gasket" one side only?
All I could think of was "anti-rattle" to keep 2 pieces of tin tight against each other.

It's not listed in the parts manual.
I took mine out and didn't replace it (making sure the cover fits tight).
With 3 tabs it's not going to come off by itself.

Don't need more loose crud floating around the oil system than necessary.

6
Buy, Sell, Trade / Re: WANTED
« on: January 15, 2025, 10:42:10 PM »
If it helps, here's a kit that includes the bolt and the spring under it. https://www.armyjeepparts.com/p-4334-oil-filter-canister-bolt-spring-set-purolator-military-junior-wwii-jeep-ajp-32145.aspx

Could be mistaken (because I didn't compare part numbers in the books) but think the bolt and spring are common to all the canister filters, military or civilian.
Several vintage military and CJ parts vendors sell them.
Pretty sure a phone call to any of them would get friendly help.

7
Rambling, Malarky, Rants, Etc... / Re: Bright Headlights
« on: October 08, 2024, 03:43:08 PM »
It is not just LEDs causing the problem, nor the switch location, but those combined with "projector beam lighting" mis-aligned or reacting to surface level changes are blinding.  Some of the vehicles also have auto "light sensors" that may be covered over or malfunctioning to add even more hazards.  Then there are the drivers that ride with their blinker or hazard lights on indefinitely???  One can't "forget" when a "Willys' one-hand signal" was "standard equipment", and 6V lights were never "too bright".  Ahhhh the good ole days...

Agree.
The design engineers and bean counters took something simple that worked and made it way over complicated (probably so the idiots would have more time to play with their so-called "smart phone" while driving).

Like a wise old plumber friend once said: "The more complex the drain, the easier it is to stop it up."

8
Rambling, Malarky, Rants, Etc... / Re: Bright Headlights
« on: October 07, 2024, 11:53:29 PM »
x2
I think it started happening when auto makers moved the high-beam switch from a foot operated button on the floor up to the turn signal arm.

Now drivers mistake the illuminated high-beam indicator lamp on the dash to mean their headlights (low beam) are on.

Idiots. Nobody reads the owners manuals.

9
So, is the 160 degree thrm just for "testing" vs running street use?
Paragraph H-7 on page 116 of the Willys Universal Jeep Service Manual calls out the standard thermostat for the CJ-2A and CJ-3A as 160-degrees (starts opening at 150* and fully open at 170*).



10
Buy, Sell, Trade / For Sale 16x5 Steel Wheels --- SOLD
« on: August 27, 2024, 03:35:14 PM »
Edit: wheels sold 10/15/2024.

For Sale.
Finally got around to getting these off my M38 in favor of correct military wheels.

Two 16x5 steel wheels.

Believe they are originals (not repops) for Willys CJ, truck, or wagon.
Lug holes not wallowed out, painted OD, no rust, some pitting, but solid and safe.
I'm CJ wheel ignorant. Am told these are early "non-creased" wheels.
One wheel has visible KH trademark and 8-48 date, the other wheel is identical but marks are obscured by pitting.
PM me for photos.

$75 each, plus shipping (to USA address only).
Located 29485.

11
Do they have "DOT" (U.S. Dept. of Transportation) and a fresh date (year) they were made printed on them?
If not, nothing but risky business using them.

12
If it helps and I read this correctly, the front cross-member on the CJ2A, CJ3A, and CJ3B are interchangeable.

https://cj3b.info/Dating/DatingFrames.html

https://cj3b.info/Tech.html

Like you found, at least one vendor seems to agree: https://www.dlbensinger.com/shop/front-frame-cross-member-mb/

Good luck!


13
Your CJ-3B Project / Re: 1953 RESCUE and RECOVERY
« on: December 02, 2023, 04:43:11 PM »
Am I missing something?
His last photo directly above showing the exposed big axle nut in the center of the hub --- is where the missing hub cap belongs.
Smaller than a tea cup. Good luck finding it on the side of the road.

Many jeep parts vendors sell replacements for a few bucks.
I think after they get pounded off and on a few times they can distort and lose their grip.

Nice pups!
What are their names?

Ruff and Ready? (R&R)

14
Your CJ-3B Project / Re: 1953 RESCUE and RECOVERY
« on: November 29, 2023, 01:56:17 PM »
Now that's a STUD.
Well done!

15
Your CJ-3A Project / Re: The shutting off problem returns
« on: November 15, 2023, 10:20:20 AM »
Because he's not using the block-mounted mechanical fuel pump and its typical metal line to the carb that sometimes gets run too near the manifold, I'd say that "heated fuel" (a.k.a. "vapor lock") is probably not the problem.
In other words, I wouldn't be looking for vapor lock until after new lines and fittings have been installed and the pump has been relocated and pressure has been verified.

The history of his Solex and whether or not it's clean and functioning correctly should also be studied.
And if that Solex banjo fitting was ruined by mating it to the wrong pipe thread fitting, good luck finding a new one.

I agree the best solution is changing back to the correct mechanical pump and Carter carb ---- and could probably be done for a couple three hundred bucks.
I bet ScoutPilot could give you a deal on both --- guaranteed to run perfectly!

Good luck!

Pages: [1] 2 3